Rule2025-06005
Airworthiness Directives; The Boeing Company Airplanes
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
April 8, 2025
Effective
May 13, 2025
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA is superseding Airworthiness Directive (AD) 2021-09- 06, which applied to all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. AD 2021-09-06 required repetitive inspections for cracking of the left- and right-hand outboard chords of certain frame fittings and failsafe straps at a certain station around eight fasteners, and repair if any cracking is found. This AD was prompted by additional reports of cracking in the area and a subsequent determination that additional inspections are needed to address the unsafe condition. This AD requires repetitive detailed and ultrasonic inspections for cracking of the left- and right-hand sides of certain frame fittings and failsafe straps, and repair if any cracking is found. The FAA is issuing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 90 Issue 66 (Tuesday, April 8, 2025)</title>
</head>
<body><pre>
[Federal Register Volume 90, Number 66 (Tuesday, April 8, 2025)]
[Rules and Regulations]
[Pages 15111-15114]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2025-06005]
========================================================================
Rules and Regulations
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains regulatory documents
having general applicability and legal effect, most of which are keyed
to and codified in the Code of Federal Regulations, which is published
under 50 titles pursuant to 44 U.S.C. 1510.
The Code of Federal Regulations is sold by the Superintendent of Documents.
========================================================================
Federal Register / Vol. 90, No. 66 / Tuesday, April 8, 2025 / Rules
and Regulations
[[Page 15111]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2024-0028; Project Identifier AD-2023-00919-T;
Amendment 39-23004; AD 2025-07-03]
RIN 2120-AA64
Airworthiness Directives; The Boeing Company Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2021-09-
06, which applied to all The Boeing Company Model 737-600, -700, -700C,
-800, -900, and -900ER series airplanes. AD 2021-09-06 required
repetitive inspections for cracking of the left- and right-hand
outboard chords of certain frame fittings and failsafe straps at a
certain station around eight fasteners, and repair if any cracking is
found. This AD was prompted by additional reports of cracking in the
area and a subsequent determination that additional inspections are
needed to address the unsafe condition. This AD requires repetitive
detailed and ultrasonic inspections for cracking of the left- and
right-hand sides of certain frame fittings and failsafe straps, and
repair if any cracking is found. The FAA is issuing this AD to address
the unsafe condition on these products.
DATES: This AD is effective May 13, 2025.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of May 13,
2025.
ADDRESSES:
AD Docket: You may examine the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-0028; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this final rule, any comments received, and other
information. The address for Docket Operations is U.S. Department of
Transportation, Docket Operations, M-30, West Building Ground Floor,
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
Material Incorporated by Reference:
<bullet> For Boeing material identified in this AD, contact Boeing
Commercial Airplanes, Attention: Contractual & Data Services (C&DS),
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600;
<a href="http://myboeingfleet.com">myboeingfleet.com</a>.
<bullet> You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St., Des
Moines, WA. For information on the availability of this material at the
FAA, call 206-231-3195. It is also available at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-0028.
FOR FURTHER INFORMATION CONTACT: Owen Bley-Male, Aviation Safety
Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone
206-231-3992; email <a href="/cdn-cgi/l/email-protection#3659415358185018545a534f1b5b575a537650575718515940"><span class="__cf_email__" data-cfemail="59362e3c37773f773b353c20743438353c193f3838773e362f">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Background
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to supersede AD 2021-09-06, Amendment 39-21519 (86 FR
23595, May 4, 2021) (AD 2021-09-06). AD 2021-09-06 applied to all The
Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER
series airplanes. The NPRM published in the Federal Register on January
16, 2024 (89 FR 2515). The NPRM was prompted by additional reports of
cracking in the area required to be inspected by AD 2021-09-06 and a
subsequent determination that additional inspections are needed to
address the unsafe condition. In the NPRM, the FAA proposed to require
repetitive detailed and ultrasonic inspections for cracking of the
left- and right-hand sides of certain frame fittings and failsafe
straps, and repair if any cracking is found. The FAA is issuing this AD
to address cracking in the station (STA) 663.75 frame fitting outboard
chords and failsafe straps adjacent to the stringer S-18A straps, which
could result in failure of a principal structural element (PSE) to
sustain limit load. The unsafe condition, if not addressed, could
adversely affect the structural integrity of the airplane and result in
loss of control of the airplane.
Discussion of Final Airworthiness Directive
Comments
The FAA received comments from four commenters, including Air Line
Pilots Association, International (ALPA), Boeing, and two individuals,
who supported the NPRM without change.
The FAA received additional comments from five commenters,
including American Airlines (American), Aviation Partners Boeing (APB),
Southwest Airlines (Southwest), Sun Country Airlines (Sun Country), and
United Airlines (United). The following presents the comments received
on the NPRM and the FAA's response to each comment.
Effect of Winglets on Accomplishment of the Proposed Actions
APB stated that the installation of blended or split scimitar
winglets per Supplemental Type Certificate (STC) ST00830SE does not
affect the actions specified in the proposed AD.
The FAA concurs with the commenter. The FAA has redesignated
paragraph (c) of the proposed AD as paragraph (c)(1) of this AD and
added paragraph (c)(2) to this AD to state that installation of STC
ST00830SE does not affect the ability to accomplish the actions
required by this AD. Therefore, for airplanes on which STC ST00830SE is
installed, a ``change in product'' alternative method of compliance
(AMOC) approval request is not necessary to comply with the
requirements of 14 CFR 39.17.
Effect of Winglets on AMOC Approval Process
APB advised that AMOCs approved by the Boeing Organization
Designation Authorization (ODA) in accordance with the process
specified in paragraph (i)(3) of the proposed AD would not be valid for
airplanes on which STC ST01697SE is installed and which have a split
scimitar winglet configuration installed by STC ST00830SE.
The FAA acknowledges and concurs with APB's assertion. However,
paragraph (i)(1) of this AD provides a provision for obtaining an AMOC
[[Page 15112]]
without using a Boeing ODA. An AMOC approval in accordance with
paragraph (i)(1) or (3) of this AD could be provided based on whether
the actions needing an AMOC apply to the APB design or the Boeing
design. No change to this AD is necessary in this regard.
Request To Add Provision To Accept Certain Previously Approved AMOCs
American, Southwest, Sun Country, and United requested similar
changes to the proposed AD to provide credit for accomplishing
replacements of the left- and right-side STA 663.75 frame fitting
assembly by accepting previously approved AMOCs. American, Southwest,
Sun Country, and United noted that they have replaced several cracked
fittings using a method approved by FAA Form 8100-9 or the AMOC process
for ADs 2021-09-06; 2019-22-10, Amendment 39-19789 (84 FR 61533,
November 13, 2019) (AD 2019-22-10); and 2019-20-02, Amendment 39-19755
(84 FR 52754, October 3, 2019) (AD 2019-20-02). In addition to a
request to accept AMOCs previously approved for ADs 2021-09-06, 2019-
22-10, and 2019-20-02, Southwest requested acceptance of global AMOC
letter 782-22-10680 for an extension of certain inspection thresholds
required by AD 2021-09-06. Southwest and United stated that the repair
instructions they used specified a 30,000-flight-cycle compliance time
before the next inspection and requested clarification on how that
compliance time in the approved repair fits with flagnote (b) in the
tables of the ``Compliance'' paragraph and Accomplishment Instructions
of Boeing Service Bulletin 737-53A1414, Revision 1, dated November 20,
2023. Sun Country also expressed concern that flagnote (b)'s reference
to repairs approved by Boeing ODAs via FAA Form 8100-9 is ``hidden'' in
the required service bulletin.
The FAA agrees to allow some previously approved AMOCs for AD 2021-
09-06, which includes previously approved AMOCs for AD 2019-22-10 and
AD 2019-20-02, in this AD. The FAA notes that flagnote (b) in certain
tables in the ``Compliance'' paragraph of Boeing Service Bulletin 737-
53A1414, Revision 1, dated November 20, 2023, states that a replaced
STA 663.75 frame fitting assembly that was accomplished using
instructions approved in FAA Form 8100-9 does not need to be inspected
for compliance with this AD. The FAA considers flagnote (b) to address
the inspection required by this AD, but flagnote (b) does not apply to
follow-on inspections specified in repair instructions. The FAA concurs
with that note for the conditions that were identified by Boeing and
has not excluded it or modified it in the exceptions identified in
paragraph (h) of this AD. It would be impractical to attempt to
identify each note or step that could be considered to contain
``hidden'' information that could be highlighted.
The FAA has added paragraph (h)(3) of this AD to clarify that for
airplanes on which the left- and right-side STA 663.75 frame fitting
assembly was replaced using instructions approved via FAA Form 8100-9,
the airplane is to be considered Configuration 2 of the applicable
group identified in Boeing Alert Requirements Bulletin 737-53A1414 RB,
Revision 1, dated November 20, 2023.
The FAA has also added paragraph (i)(4) of this AD to provide
acceptance for some previously approved AMOCs provided certain
conditions are met.
Request for Reduced Inspection Interval Alternative to Corrective
Action
Sun Country requested that a reduced inspection schedule monitor be
used in lieu of replacement before further flight if cracking is found
on the far fasteners during the required ultrasonic inspection. Sun
Country explained that based on its experience with certain inspection
procedures in the non-destructive testing manual, inspecting the far
fasteners as specified might lead to false cracking indications. Sun
Country suggested that cracking at the affected failsafe strap location
would become evident when inspections are conducted on a reduced
interval.
The FAA does not agree with the request. Generally, the FAA does
not allow an airplane to fly with a known crack. The FAA does not have
the data in this case to substantiate allowing further flight with a
known unsafe condition, on the chance that the required inspection
returns a false positive result. However, under the provisions
specified in paragraph (i) of this AD, the FAA will consider requests
to extend the compliance time for repairs if sufficient data are
submitted to substantiate that the new compliance time would provide an
acceptable level of safety. This AD has not been changed regarding this
issue.
Conclusion
The FAA reviewed the relevant data, considered any comments
received, and determined that air safety requires adopting this AD as
proposed. Accordingly, the FAA is issuing this AD to address the unsafe
condition on these products. Except for minor editorial changes, and
any other changes described previously, this AD is adopted as proposed
in the NPRM. None of the changes will increase the economic burden on
any operator.
Material Incorporated by Reference Under 1 CFR Part 51
The FAA reviewed Boeing Alert Requirements Bulletin 737-53A1414 RB,
Revision 1, dated November 20, 2023. This material specifies procedures
for repetitive internal detailed inspection for cracking of the frame
fitting and visible areas of the failsafe strap at STA 663.73 (left-
and right-hand sides), repetitive external detailed and ultrasonic
inspections for cracking of the failsafe strap at STA 663.75 (left- and
right-hand sides), and repair if any cracking is found. This material
is reasonably available because the interested parties have access to
it through their normal course of business or by the means identified
in the ADDRESSES section.
Costs of Compliance
The FAA estimates that this AD affects 1,911 airplanes of U.S.
registry. The FAA estimates the following costs to comply with this AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost on U.S.
Action Labor cost Parts cost Cost per product operators
----------------------------------------------------------------------------------------------------------------
Inspection....................... 4 work-hours x $85 $0 $340 per inspection $649,740 per
per hour = $340 cycle. inspection cycle.
per inspection
cycle.
----------------------------------------------------------------------------------------------------------------
The FAA has received no definitive data on which to base the cost
estimates for the on-condition repairs specified in this AD.
The FAA has included all known costs in its cost estimate.
According to
[[Page 15113]]
the manufacturer, however, some or all of the costs of this AD may be
covered under warranty, thereby reducing the cost impact on affected
operators.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by:
0
a. Removing Airworthiness Directive (AD) 2021-09-06, Amendment 39-21519
(86 FR 23595, May 4, 2021); and
0
b. Adding the following new AD:
2025-07-03 The Boeing Company: Amendment 39-23004; Docket No. FAA-
2024-0028; Project Identifier AD-2023-00919-T.
(a) Effective Date
This airworthiness directive (AD) is effective May 13, 2025.
(b) Affected ADs
This AD replaces AD 2021-09-06, Amendment 39-21519 (86 FR 23595,
May 4, 2021) (AD 2021-09-06).
(c) Applicability
(1) This AD applies to all The Boeing Company Model 737-600, -
700, -700C, -800, -900, and -900ER series airplanes, certificated in
any category.
(2) Installation of Supplemental Type Certificate (STC)
ST00830SE does not affect the ability to accomplish the actions
required by this AD. Therefore, for airplanes on which STC ST00830SE
is installed, a ``change in product'' alternative method of
compliance (AMOC) approval request is not necessary to comply with
the requirements of 14 CFR 39.17.
(d) Subject
Air Transport Association (ATA) of America Code 53, Fuselage.
(e) Unsafe Condition
This AD was prompted by reports of cracking in the station (STA)
663.75 frame fitting outboard chords and failsafe straps adjacent to
the stringer S-18A area and a determination that additional
inspections are needed to address the unsafe condition. The FAA is
issuing this AD to address cracking in the STA 663.75 frame fitting
outboard chords and failsafe straps adjacent to the stringer S-18A
straps, which could result in failure of a principal structural
element (PSE) to sustain limit load. The unsafe condition, if not
addressed, could adversely affect the structural integrity of the
airplane and result in loss of control of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Actions
Except as specified by paragraph (h) of this AD: At the
applicable times specified in the ``Compliance'' paragraph of Boeing
Alert Requirements Bulletin 737-53A1414 RB, Revision 1, dated
November 20, 2023, do all applicable actions identified in, and in
accordance with, the Accomplishment Instructions of Boeing Alert
Requirements Bulletin 737-53A1414 RB, Revision 1, dated November 20,
2023.
Note 1 to paragraph (g): Guidance for accomplishing the actions
required by this AD can be found in Boeing Alert Service Bulletin
737-53A1414, Revision 1, dated November 20, 2023, which is referred
to in Boeing Alert Requirements Bulletin 737-53A1414 RB, Revision 1,
dated November 20, 2023.
(h) Exceptions to Requirements Bulletin Specifications
(1) Where the Condition and Compliance Time columns of the
tables in the ``Compliance'' paragraph of Boeing Alert Requirements
Bulletin 737-53A1414 RB, Revision 1, dated November 20, 2023, use
the phrase ``the original issue date of Requirements Bulletin 737-
53A1414 RB,'' or ``the Revision 1 date of Requirements Bulletin 737-
53A1414 RB,'' this AD requires using the effective date of this AD.
(2) Where Boeing Alert Requirements Bulletin 737-53A1414 RB,
Revision 1, dated November 20, 2023, specifies contacting Boeing for
repair instructions: This AD requires doing the repair using a
method approved in accordance with the procedures specified in
paragraph (i) of this AD.
(3) For airplanes on which the left- and right-side STA 663.75
frame fitting assembly was replaced using instructions approved via
FAA Form 8100-9, the airplane is to be considered Configuration 2 of
the applicable group as identified in Boeing Alert Requirements
Bulletin 737-53A1414 RB, Revision 1, dated November 20, 2023.
(i) Alternative Methods of Compliance (AMOCs)
(1) The Manager, AIR-520, Continued Operational Safety Branch,
FAA, has the authority to approve AMOCs for this AD, if requested
using the procedures found in 14 CFR 39.19. In accordance with 14
CFR 39.19, send your request to your principal inspector or
responsible Flight Standards Office, as appropriate. If sending
information directly to the manager of the certification office,
send it to the attention of the person identified in paragraph
(j)(1) of this AD. Information may be emailed to: <a href="/cdn-cgi/l/email-protection#c1808c8e8281a7a0a0efa6aeb7"><span class="__cf_email__" data-cfemail="73323e3c30331512125d141c05">[email protected]</span></a>.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the responsible Flight Standards Office.
(3) An AMOC that provides an acceptable level of safety may be
used for any repair, modification, or alteration required by this AD
if it is approved by The Boeing Company Organization Designation
Authorization (ODA) that has been authorized by the Manager, AIR-
520, Continued Operational Safety Branch, FAA, to make those
findings. To be approved, the repair method, modification deviation,
or alteration deviation must meet the certification basis of the
airplane, and the approval must specifically refer to this AD.
(4) AMOCs previously approved for replacement of the STA 663.75
frame fitting assembly and related work requirements of AD 2021-09-
06 are approved as AMOCs for the corresponding provisions of Boeing
Alert Requirements Bulletin 737-53A1414 RB, Revision 1, dated
November 20, 2023, that are required by paragraph (g) of this AD,
except for AMOCs that include any defined initial (also known as
`threshold') and repetitive inspections, which must also meet
[[Page 15114]]
the conditions specified in paragraphs (i)(4)(i) and (ii) of this
AD.
(i) The inspection areas and methods in figure 1 and figure 2 of
Boeing Alert Requirements Bulletin 737-53A1414 RB, Revision 1, dated
November 20, 2023, are included in all initial (also known as
`threshold') and repetitive inspections.
(ii) The initial (or threshold) inspection is the applicable
time specified in paragraph (i)(4)(ii)(A) or (B) of this AD.
(A) For airplanes identified as Group 1 airplanes in Boeing
Alert Requirements Bulletin 737-53A1414 RB, Revision 1, dated
November 20, 2023: Within 30,000 flight cycles from the date of the
applicable FAA Form 8100-9 approval.
(B) For airplanes identified as Group 2 airplanes in Boeing
Alert Requirements Bulletin 737-53A1414 RB, Revision 1, dated
November 20, 2023: Within 18,000 flight cycles from the date of the
applicable FAA Form 8100-9 approval.
(j) Related Information
(1) For more information about this AD, contact Owen Bley-Male,
Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA
98198; telephone 206-231-3992; email <a href="/cdn-cgi/l/email-protection#543b23313a7a327a3638312d7939353831143235357a333b22"><span class="__cf_email__" data-cfemail="93fce4f6fdbdf5bdf1fff6eabefef2fff6d3f5f2f2bdf4fce5">[email protected]</span></a>.
(2) Material identified in this AD that is not incorporated by
reference is available at the addresses specified in paragraph
(k)(3) of this AD.
(k) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the material listed in this
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this material as applicable to do the actions
required by this AD, unless this AD specifies otherwise.
(i) Boeing Alert Requirements Bulletin 737-53A1414 RB, Revision
1, dated November 20, 2023.
(ii) [Reserved]
(3) For Boeing material identified in this AD, contact Boeing
Commercial Airplanes, Attention: Contractual & Data Services (C&DS),
2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600;
<a href="http://myboeingfleet.com">myboeingfleet.com</a>.
(4) You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St.,
Des Moines, WA. For information on the availability of this material
at the FAA, call 206-231-3195.
(5) You may view this material at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, visit <a href="http://www.archives.gov/federal-register/cfr/ibr-locations">www.archives.gov/federal-register/cfr/ibr-locations</a> or email <a href="/cdn-cgi/l/email-protection#0f697d2166617c7f6a6c7b6660614f616e7d6e21686079"><span class="__cf_email__" data-cfemail="88eefaa6e1e6fbf8edebfce1e7e6c8e6e9fae9a6efe7fe">[email protected]</span></a>.
Issued on March 25, 2025.
Victor Wicklund,
Deputy Director, Integrated Certificate Management Division, Aircraft
Certification Service.
[FR Doc. 2025-06005 Filed 4-7-25; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on April 8, 2025.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.