Rule2024-28130
Airworthiness Directives; Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP)) Airplanes
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
December 2, 2024
Effective
January 6, 2025
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This AD was prompted by reports that the pylon-to-wing area motive flow flexible fuel line assemblies may have been installed incorrectly. This AD requires inspecting the motive flow fuel line assemblies and performing corrective actions as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 89 Issue 231 (Monday, December 2, 2024)</title>
</head>
<body><pre>
[Federal Register Volume 89, Number 231 (Monday, December 2, 2024)]
[Rules and Regulations]
[Pages 95098-95100]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2024-28130]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2024-1474; Project Identifier MCAI-2023-01014-T;
Amendment 39-22884; AD 2024-23-05]
RIN 2120-AA64
Airworthiness Directives; Airbus Canada Limited Partnership (Type
Certificate Previously Held by C Series Aircraft Limited Partnership
(CSALP)) Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for
certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500-
1A11 airplanes. This AD was prompted by reports that the pylon-to-wing
area motive flow flexible fuel line assemblies may have been installed
incorrectly. This AD requires inspecting the motive flow fuel line
assemblies and performing corrective actions as specified in a
Transport Canada AD, which is incorporated by reference. The FAA is
issuing this AD to address the unsafe condition on these products.
DATES: This AD is effective January 6, 2025.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of January 6,
2025.
ADDRESSES:
AD Docket: You may examine the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-1474; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this final rule, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
address for Docket Operations is U.S. Department of Transportation,
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200
New Jersey Avenue SE, Washington, DC 20590.
Material Incorporated by Reference:
<bullet> For Transport Canada material identified in this AD,
contact Transport Canada, Transport Canada National Aircraft
Certification, 159 Cleopatra Drive, Nepean, Ontario K1A 0N5, Canada;
telephone 888-663-3639; email <a href="/cdn-cgi/l/email-protection#7327305d321a01041c01071b1a1d160000371a011610071a0516005e301c1d001a141d160017161d12051a1412111a1f1a07165d27303307105d14105d1012"><span class="__cf_email__" data-cfemail="6034234e210912170f121408090e051313240912050314091605134d230f0e1309070e051304050e011609070102090c0914054e34232014034e07034e0301">[email protected]</span></a>; website at tc.canada.ca/en/
aviation.
<bullet> You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St., Des
Moines, WA. For information on the availability of this material at the
FAA, call 206-231-3195. It is also available at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-1474.
FOR FURTHER INFORMATION CONTACT: Joseph Catanzaro, Aviation Safety
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590;
telephone 516-228-7300; email <a href="/cdn-cgi/l/email-protection#2c46435f495c44024f4d584d42564d5e436c4a4d4d024b435a"><span class="__cf_email__" data-cfemail="7f15100c1a0f17511c1e0b1e11051e0d103f191e1e51181009">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Background
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 by adding an AD that would apply to certain Airbus Canada
Limited Partnership Model BD-500-1A10 and BD-500-1A11 airplanes. The
NPRM published in the Federal Register on May 23, 2024 (89 FR 45610).
The NPRM was prompted by AD CF-2023-64, dated September 18, 2023,
issued by Transport Canada, which is the aviation authority for Canada
(referred to after this as the MCAI). The MCAI states that reports have
been received indicating that the pylon-to-wing area motive flow
flexible fuel line assemblies may have been installed incorrectly,
potentially resulting in a twist to the motive flow fuel line.
In the NPRM, the FAA proposed to require inspecting the motive flow
fuel line assemblies and corrective actions, as specified in Transport
Canada AD CF-2023-64. The FAA is issuing this AD to address a possible
abrasion of the fuel line causing a fuel leak; if not addressed, the
electrical harness connectors in the wing area could be a potential
ignition source and pose a risk of fire.
You may examine the MCAI in the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-1474.
Discussion of Final Airworthiness Directive
Comments
The FAA received a comment from Air Line Pilots Association,
International (ALPA), who supported the NPRM without change.
The FAA received an additional comment from Delta Airlines. The
following presents the comment received on the NPRM and the FAA's
response to the comment.
Request for Change to Exceptions Paragraph
Delta requested revising paragraph (h)(3) by removing the word
``flexible'' and revising certain punctuation. Delta stated the term
``flexible'' is used only when referring to the flexible-hose assembly
installed in the shroud assembly. Therefore, the flexible-hose assembly
and the shroud assembly are subassemblies of the fuel motive-flow tube
assembly.
The FAA agrees that the term ``flexible'' should be removed in
reference to the entire motive flow fuel line assemblies since the
service information referenced in Transport Canada AD CF-2023-64
requires replacement of the fuel motive-flow tube assembly if damage is
found on either the flexible-hose assembly or the shroud assembly.
Conclusion
This product has been approved by the aviation authority of another
country and is approved for operation in the United States. Pursuant to
the FAA's bilateral agreement with this State of Design Authority, it
has notified the FAA of the unsafe condition described in the MCAI
referenced above. The FAA reviewed the relevant data, considered the
comments received, and determined that air safety requires adopting
this AD as proposed. Accordingly, the FAA is issuing this AD to address
the unsafe condition on this product. Except for minor editorial
changes, and any other changes described previously, this AD is adopted
as proposed in the NPRM. None of the changes will increase the economic
burden on any operator.
Material Incorporated by Reference Under 1 CFR Part 51
The FAA reviewed AD CF-2023-64, dated September 18, 2023. This
material specifies procedures for a general visual inspection of the
left and right motive flow flexible fuel line assemblies for twisted or
damaged fuel lines or damaged shrouds, and replacement of motive flow
fuel line assemblies with twisted or damaged fuel lines or damaged
shrouds.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
[[Page 95099]]
Costs of Compliance
The FAA estimates that this AD affects 93 airplanes of U.S.
registry. The FAA estimates the following costs to comply with this AD:
Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
7 work-hours x $85 per hour = $595........................... $0 $0 $55,335
----------------------------------------------------------------------------------------------------------------
The FAA estimates the following costs to do any on-condition
actions that would be required based on the results of any required
actions. The FAA has no way of determining the number of aircraft that
might need this on-condition action:
Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
Cost per
Labor cost Parts cost product
------------------------------------------------------------------------
1 work-hour x $85 per hour = $85...... $2,500 $2,585
------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
2024-23-05 Airbus Canada Limited Partnership (Type Certificate
Previously Held by C Series Aircraft Limited Partnership (CSALP);
Bombardier, Inc.): Amendment 39-22884; Docket No. FAA-2024-1474;
Project Identifier MCAI-2023-01014-T.
(a) Effective Date
This airworthiness directive (AD) is effective January 6, 2025.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Airbus Canada Limited Partnership (Type
Certificate previously held by C Series Aircraft Limited Partnership
(CSALP); Bombardier, Inc.) Model BD-500-1A10 and BD-500-1A11
airplanes, certificated in any category, as identified in Transport
Canada AD CF-2023-64, dated September 18, 2023 (Transport Canada AD
CF-2023-64).
(d) Subject
Air Transport Association (ATA) of America Code 28, Fuel.
(e) Unsafe Condition
This AD was prompted by reports that the pylon-to-wing area
motive flow flexible fuel line assemblies may have been installed
incorrectly. The FAA is issuing this AD to ensure the motive flow
flexible fuel line assemblies are installed correctly. The unsafe
condition, if not addressed, could result in abrasion of the fuel
line and a possible fuel leak; as a result, the electrical harness
connectors in the wing area could be a potential ignition source and
pose a risk of fire.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, Transport Canada AD CF-2023-64.
(h) Exception to Transport Canada AD CF-2023-64
(1) Where Transport Canada AD CF-2023-64 refers to its effective
date, this AD requires using the effective date of this AD.
(2) Where Transport Canada AD CF-2023-64 refers to hours air
time, this AD requires using flight hours.
(3) Where the Corrective Actions paragraph of Transport Canada
AD CF-2023-64 specifies to ``Inspect and, if necessary, replace the
left and right motive flow fuel line assemblies,'' for this AD,
replace that text with ``Inspect and, as applicable, replace the
left and right motive flow fuel line assemblies.''
[[Page 95100]]
(i) Additional AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Validation Branch, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. In accordance with 14 CFR 39.19, send your request to your
principal inspector or responsible Flight Standards Office, as
appropriate. If sending information directly to the manager of the
International Validation Branch, mail it to the address identified
in paragraph (j) of this AD. Information may be emailed to: <a href="/cdn-cgi/l/email-protection#d7eefa968184fa998e969498fa94988497b1b6b6f9b0b8a1"><span class="__cf_email__" data-cfemail="447d69051217690a1d05070b69070b17042225256a232b32">[email protected]</span></a>. Before using any approved AMOC, notify your
appropriate principal inspector, or lacking a principal inspector,
the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, International
Validation Branch, FAA; or Transport Canada; or Airbus Canada
Limited Partnership's Transport Canada Design Approval Organization
(DAO). If approved by the DAO, the approval must include the DAO-
authorized signature.
(j) Additional Information
For more information about this AD, contact Joseph Catanzaro,
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410,
Westbury, NY 11590; telephone 516-228-7300; email
<a href="/cdn-cgi/l/email-protection#a0cacfd3c5d0c88ec3c1d4c1cedac1d2cfe0c6c1c18ec7cfd6"><span class="__cf_email__" data-cfemail="147e7b6771647c3a777560757a6e75667b547275753a737b62">[email protected]</span></a>.
(k) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless this AD specifies otherwise.
(i) Transport Canada AD CF-2023-64, dated September 18, 2023.
(ii) [Reserved]
(3) For Transport Canada AD CF-2023-64, contact Transport
Canada, Transport Canada National Aircraft Certification, 159
Cleopatra Drive, Nepean, Ontario K1A 0N5, Canada; telephone 888-663-
3639; email <a href="/cdn-cgi/l/email-protection#297d6a0768405b5e465b5d4140474c5a5a6d405b4c4a5d405f4c5a046a46475a404e474c5a4d4c47485f404e484b4045405d4c077d6a695d4a074e4a074a48"><span class="__cf_email__" data-cfemail="80d4c3aec1e9f2f7eff2f4e8e9eee5f3f3c4e9f2e5e3f4e9f6e5f3adc3efeef3e9e7eee5f3e4e5eee1f6e9e7e1e2e9ece9f4e5aed4c3c0f4e3aee7e3aee3e1">[email protected]</span></a>. You may find this Transport
Canada AD on the Transport Canada website tc.canada.ca/en/aviation.
(4) You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th
Street, Des Moines, WA. For information on the availability of this
material at the FAA, call 206-231-3195.
(5) You may view this material at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, visit <a href="http://www.archives.gov/federal-register/cfr/ibr-locations">www.archives.gov/federal-register/cfr/ibr-locations</a>, or email <a href="/cdn-cgi/l/email-protection#6107134f080f1211040215080e0f210f0013004f060e17"><span class="__cf_email__" data-cfemail="3553471b5c5b46455056415c5a5b755b5447541b525a43">[email protected]</span></a>.
Issued on November 12, 2024.
Peter A. White,
Deputy Director, Integrated Certificate Management Division, Aircraft
Certification Service.
[FR Doc. 2024-28130 Filed 11-29-24; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on December 2, 2024.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.