Rule2024-18586
Airworthiness Directives; Air Tractor, Inc. Airplanes
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
August 20, 2024
Effective
September 4, 2024
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA is superseding Airworthiness Directive (AD) 2023-15- 07, which applied to all Air Tractor, Inc. (Air Tractor) Model AT-802 and AT-802A airplanes with Wipaire, Inc. Supplemental Type Certificate (STC) No. SA01795CH installed. AD 2023-15-07 required repetitively inspecting the left and right forward horizontal stabilizer spars for cracks, replacing any forward horizontal stabilizer spar found cracked, and reporting inspection results to the FAA. This AD requires repetitively inspecting the left and right, forward and rear, horizontal stabilizer spars for cracks at shorter intervals than those required by AD 2023-15-07, replacing any horizontal stabilizer spar found cracked or damaged, installing bathtub fittings, and reporting inspection results to the FAA. This AD was prompted by additional reports of cracks in the horizontal stabilizer spars and the need to incorporate a new finlet attach design on the horizontal stabilizer spars to reduce the cracking. The FAA is issuing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 89 Issue 161 (Tuesday, August 20, 2024)</title>
</head>
<body><pre>
[Federal Register Volume 89, Number 161 (Tuesday, August 20, 2024)]
[Rules and Regulations]
[Pages 67267-67270]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2024-18586]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2024-2013; Project Identifier AD-2024-00363-A;
Amendment 39-22812; AD 2024-16-06]
RIN 2120-AA64
Airworthiness Directives; Air Tractor, Inc. Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2023-15-
07, which applied to all Air Tractor, Inc. (Air Tractor) Model AT-802
and AT-802A airplanes with Wipaire, Inc. Supplemental Type Certificate
(STC) No. SA01795CH installed. AD 2023-15-07 required repetitively
inspecting the left and right forward horizontal stabilizer spars for
cracks, replacing any forward horizontal stabilizer spar found cracked,
and reporting inspection results to the FAA. This AD requires
repetitively inspecting the left and right, forward and rear,
horizontal stabilizer spars for cracks at shorter intervals than those
required by AD 2023-15-07, replacing any horizontal stabilizer spar
found cracked or damaged, installing bathtub fittings, and reporting
inspection results to the FAA. This AD was prompted by additional
reports of cracks in the horizontal stabilizer spars and the need to
incorporate a new finlet attach design on the horizontal stabilizer
spars to reduce the cracking. The FAA is issuing this AD to address the
unsafe condition on these products.
DATES: This AD is effective September 4, 2024.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of September 4,
2024.
The FAA must receive comments on this AD by October 4, 2024.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
<bullet> Federal eRulemaking Portal: Go to <a href="http://regulations.gov">regulations.gov</a>. Follow
the instructions for submitting comments.
<bullet> Fax: (202) 493-2251.
<bullet> Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
<bullet> Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket: You may examine the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-2013; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this final rule, any comments received, and other
information. The street address for Docket Operations is listed above.
Material Incorporated by Reference:
<bullet> For Wipaire, Inc. material identified in this AD, contact
Wipaire, Inc., 1700 Henry Avenue, Fleming Field (KSGS), South St. Paul,
MN 55075; phone: (651) 451-1205; email: <a href="/cdn-cgi/l/email-protection#30534543445f5d554243554246595355700c5110584255560d" http: wipaire.com">wipaire.com</a>">customerservice@<a href="http://wipaire.com">wipaire.com</a></a>;
website: <a href="http://wipaire.com">wipaire.com</a>.
<bullet> You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 901 Locust, Kansas City,
MO 64106. For information on the availability of this material at the
FAA, call (817) 222-5110. It is also available at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-2013.
FOR FURTHER INFORMATION CONTACT: Tim Eichor, Aviation Safety Engineer,
Central Certification Branch, FAA, 1801 S. Airport Road, Wichita, KS
67209; phone: (847) 294-7141; email: <a href="/cdn-cgi/l/email-protection#cbbfa2a6e5afe5aea2a8a3a4b98badaaaae5aca4bd"><span class="__cf_email__" data-cfemail="1064797d3e743e757973787f62507671713e777f66">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written data, views, or arguments
about this final rule. Send your comments to an address listed under
the ADDRESSES section. Include ``Docket No. FAA-2024-2013; Project
Identifier AD-2024-00363-A'' at the beginning of your comments. The
most helpful comments reference a specific portion of the final rule,
explain the reason for any recommended change, and include supporting
data. The FAA will consider all comments received by the closing date
and may amend this final rule because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
<a href="http://regulations.gov">regulations.gov</a>, including any personal information you provide. The
agency will also post a report summarizing each substantive verbal
contact received about this final rule.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this AD contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this AD, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this AD. Submissions containing CBI should be sent to Tim
Eichor, Aviation Safety Engineer, Central Certification Branch, FAA,
1801 S. Airport Road, Wichita, KS 67209. Any commentary that the FAA
receives which is not specifically designated as CBI will be placed in
the public docket for this rulemaking.
Background
The FAA issued AD 2023-15-07, Amendment 39-22519 (88 FR 53761,
August 9, 2023) (AD 2023-15-07), for all Air Tractor Model AT-802 and
AT-802A airplanes with Wipaire, Inc. STC No. SA01795CH installed. AD
2023-15-07 required repetitively inspecting the left and right forward
horizontal stabilizer spars for cracks, replacing any forward
horizontal stabilizer spar found cracked, and reporting inspection
results to the FAA. For certain airplanes, AD 2023-15-07 required the
inspection before the airplane accumulated 200 hours time-in-service
(TIS) after installation of STC No. SA01795CH. AD 2023-15-07 resulted
from cracks found in the forward horizontal stabilizer spar bend radius
located at the STC finlet mounting locations. The FAA issued AD 2023-
15-07 to detect and correct cracks in the forward horizontal stabilizer
spar, which could result in structural failure of the horizontal tail
with consequent loss of control of the airplane.
Actions Since AD 2023-15-07 Was Issued
As a result of the reports of the inspections required by AD 2023-
15-07, additional cracks have been found in the forward horizontal
stabilizer spar, including cracks found before the airplane accumulated
200 hours TIS after installation of the STC.
[[Page 67268]]
Accordingly, the FAA determined that reducing the inspection interval
is necessary. In addition, based on a new fatigue analysis, the FAA
determined that there is the potential for cracks in the rear
horizontal stabilizer spar. Wipaire, Inc. has developed a change to STC
No. SA01795CH, which incorporates an improved design that includes
modification kits to install bathtub fittings on the horizontal
stabilizer spars to mitigate this condition by improving the structural
load path. This includes more accessible repetitive inspection
intervals of 110 hours TIS. The FAA is issuing this AD to address the
unsafe condition on these products.
FAA's Determination
The FAA is issuing this AD because the agency determined the unsafe
condition described previously is likely to exist or develop in other
products of the same type design.
Material Incorporated by Reference Under 1 CFR Part 51
The FAA reviewed Wipaire, Inc. Service Letter 253, Revision D,
dated July 3, 2024 (Wipaire SL 253D), which specifies procedures for
repetitively inspecting the left and right, forward and rear,
horizontal stabilizer spars for cracks and installing bathtub fittings
using Service Kit 1012347-01 or 1012347-02. This material also
specifies procedures for repetitively inspecting the left and right,
forward and rear, horizontal stabilizer spars for cracks, elongated
holes, and corrosion after installation of the bathtub fittings. This
material is reasonably available because the interested parties have
access to it through their normal course of business or by the means
identified in the ADDRESSES section.
AD Requirements
This AD retains none of the requirements of AD 2023-15-07. This AD
requires repetitively inspecting both the left and right, forward and
rear, horizontal stabilizer spars for cracks, replacing any horizontal
stabilizer spar found cracked or damaged, installing bathtub fittings
(Service Kit 1012347-01 or 1012347-02), and reporting inspection
results to the FAA. The inspection intervals in this AD are shorter
than the intervals required by AD 2023-15-07.
Differences Between This AD and the Referenced Material
As part of the instructions for installing the bathtub fittings,
Wipaire SL 253D specifies that to be eligible for reinstallation,
finlet mount weldments must include a certain welded gusset, but that
constraint is not required by this AD.
Wipaire SL 253D includes an inspection of the finlets and forward
bathtub fittings at intervals of 1,500 hours TIS and establishes a life
limit of 7,800 hours TIS on the forward spar and forward bathtub
fittings. This AD does not include those requirements because the
compliance times would allow sufficient time to provide notice and
opportunity for public comment. The FAA is evaluating these actions and
may consider future rulemaking.
This AD requires an initial compliance time of within 7 days or
before the airplane accumulates 110 hours TIS since installation of STC
No. SA01795CH, whichever occurs later, while Wipaire SL 253D specifies
different compliance times for different configurations of STC No.
SA01795CH.
Wipaire SL 253D specifies repeating the inspections at intervals of
200 hours TIS, but this AD requires the repetitive inspections at
intervals not to exceed 110 hours TIS.
Interim Action
The FAA considers this AD to be an interim action. The FAA is
evaluating the need to establish a life limit (potentially as low as
2,000 hours TIS) on the horizontal stabilizer spars to further mitigate
the unsafe condition long term. The FAA may consider future rulemaking
on this subject.
Justification for Immediate Adoption and Determination of the Effective
Date
Section 553(b) of the Administrative Procedure Act (APA) (5 U.S.C.
551 et seq.) authorizes agencies to dispense with notice and comment
procedures for rules when the agency, for ``good cause,'' finds that
those procedures are ``impracticable, unnecessary, or contrary to the
public interest.'' Under this section, an agency, upon finding good
cause, may issue a final rule without providing notice and seeking
comment prior to issuance. Further, section 553(d) of the APA
authorizes agencies to make rules effective in less than thirty days,
upon a finding of good cause.
An unsafe condition exists that requires the immediate adoption of
this AD without providing an opportunity for public comments prior to
adoption. The FAA has found that the risk to the flying public
justifies forgoing notice and comment prior to adoption of this rule
because cracks in the horizontal stabilizer spars could lead to
structural failure of the horizontal tail with consequent loss of
control of the airplane. Airplanes with the affected STC installed are
used in fire-fighting missions and put frequent high repetitive fatigue
loads in this area at a high utilization rate (about 100 hours TIS
monthly). Based on the number of cracks found to date, a significant
number of airplanes need to be inspected within 7 days after the
effective date of this AD and modified with bathtub fittings within 300
hours TIS (about 3 months for the high utilization airplanes). These
compliance times are shorter than the time necessary for the public to
comment and for publication of the final rule. Accordingly, notice and
opportunity for prior public comment are impracticable and contrary to
the public interest pursuant to 5 U.S.C. 553(b).
In addition, the FAA finds that good cause exists pursuant to 5
U.S.C. 553(d) for making this amendment effective in less than 30 days,
for the same reasons the FAA found good cause to forgo notice and
comment.
Regulatory Flexibility Act
The requirements of the Regulatory Flexibility Act (RFA) do not
apply when an agency finds good cause pursuant to 5 U.S.C. 553 to adopt
a rule without prior notice and comment. Because FAA has determined
that it has good cause to adopt this rule without prior notice and
comment, RFA analysis is not required.
Costs of Compliance
The FAA estimates that this AD affects 30 airplanes of U.S.
registry.
The FAA estimates the following costs to comply with this AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost on U.S.
Action Labor cost Parts cost Cost per airplane operators
----------------------------------------------------------------------------------------------------------------
Inspect horizontal stabilizer 20 work-hours x $85 $0 $1,700 per $51,000 per
spars (without bathtub fittings). per hour = $1,700. inspection cycle. inspection cycle.
Install bathtub fittings......... 40 work-hours x $85 3,100 $6,500............. $195,000.
per hour = $3,400.
[[Page 67269]]
Inspect horizontal stabilizer 3 work-hours x $85 0 $255 per inspection $7,650 per
spars (with bathtub fittings). per hour = $255. cycle. inspection cycle.
Report inspection results........ 1 work-hour x $85 0 $85 per inspection $2,550 per
per hour = $85. cycle. inspection cycle.
----------------------------------------------------------------------------------------------------------------
The FAA estimates the following costs to do any necessary
replacements that would be required based on the results of the
inspection. The agency has no way of determining the number of
airplanes that might need this replacement:
On-Condition Costs
----------------------------------------------------------------------------------------------------------------
Cost per
Action Labor cost Parts cost airplane
----------------------------------------------------------------------------------------------------------------
Replace horizontal stabilizer spar............ 40 work-hours x $85 per hour = $2,800 $6,200
$3,400.
----------------------------------------------------------------------------------------------------------------
The FAA has included all known costs in its cost estimate.
According to the manufacturer, however, some of the costs of this AD
may be covered under warranty, thereby reducing the cost impact on
affected operators.
Paperwork Reduction Act
A federal agency may not conduct or sponsor, and a person is not
required to respond to, nor shall a person be subject to a penalty for
failure to comply with a collection of information subject to the
requirements of the Paperwork Reduction Act unless that collection of
information displays a currently valid OMB Control Number. The OMB
Control Number for this information collection is 2120-0056. Public
reporting for this collection of information is estimated to be
approximately 1 hour per response, including the time for reviewing
instructions, searching existing data sources, gathering and
maintaining the data needed, and completing and reviewing the
collection of information. All responses to this collection of
information are mandatory. Send comments regarding this burden estimate
or any other aspect of this collection of information, including
suggestions for reducing this burden to: Information Collection
Clearance Officer, Federal Aviation Administration, 10101 Hillwood
Parkway, Fort Worth, TX 76177-1524.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866, and
(2) Will not affect intrastate aviation in Alaska.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by:
0
a. Removing Airworthiness Directive 2023-15-07, Amendment 39-22519 (88
FR 53761, August 9, 2023); and
0
b. Adding the following new airworthiness directive:
2024-16-06 Air Tractor, Inc.: Amendment 39-22812; Docket No. FAA-
2024-2013; Project Identifier AD-2024-00363-A.
(a) Effective Date
This airworthiness directive (AD) is effective September 4,
2024.
(b) Affected ADs
This AD replaces AD 2023-15-07, Amendment 39-22519 (88 FR 53761,
August 9, 2023) (AD 2023-15-07).
(c) Applicability
This AD applies to Air Tractor, Inc. Model AT-802 and AT-802A
airplanes, all serial numbers, certificated in any category, that
have Wipaire, Inc. Supplemental Type Certificate (STC) No. SA01795CH
installed.
(d) Subject
Joint Aircraft System Component (JASC) Code 5510, Horizontal
Stabilizer Structure; 5511 Horizontal stabilizer, Spar/Rib; 5514,
Horizontal Stabilizer Miscellaneous Structure; 5530, Vertical
Stabilizer Structure.
(e) Unsafe Condition
This AD was prompted by additional reports of cracks found in
the horizontal stabilizer spars and the need to incorporate a new
finlet attach design on the horizontal stabilizer spars to reduce
the cracking. The FAA is issuing this AD to prevent structural
failure of the horizontal stabilizer spars. The unsafe condition, if
not addressed, could result in structural failure of the horizontal
[[Page 67270]]
tail with consequent loss of control of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Actions
(1) Within 7 days after the effective date of this AD or before
the airplane accumulates 110 hours time-in-service (TIS) after
installation of STC No. SA01795CH, whichever occurs later, and
thereafter at intervals not to exceed 110 hours TIS until the
airplane is modified as required by paragraph (g)(3) of this AD:
Inspect the left and right horizontal stabilizer spars for cracks in
accordance with Steps 1 through 9 of the Work Instructions--
Inspection, Method 1 in Wipaire, Inc. Service Letter 253, Revision
D, dated July 3, 2024 (Wipaire SL 253D).
(2) If any crack is found in a horizontal stabilizer spar during
any inspection required by paragraph (g)(1) of this AD, or if any
crack, elongated hole, or corrosion is found in a horizontal
stabilizer spar during any inspection required by paragraph (g)(4)
of this AD, before further flight, replace the horizontal stabilizer
spar.
(3) Within 300 hours TIS or 12 months after the effective date
of this AD, whichever occurs first, install bathtub fittings
(Service Kit 1012347-01 or 1012347-02) in accordance with Steps 1
through 10 of the Work Instructions--Install Bathtub Fittings in
Wipaire SL 253D except where Step 2 specifies that to be eligible
for reinstallation, finlet mount weldments must include the welded
gussets shown in figure 8 of Wipaire SL 253D, that constraint is not
required by this AD. If any spars were previously modified by
installing 7D1-4399 Revision L or earlier, regardless of condition,
those spars must be replaced at the same time the bathtub fittings
kit is installed.
(4) Within 110 hours TIS after installing the bathtub fittings,
and thereafter at intervals not to exceed 110 hours TIS, inspect the
horizontal stabilizer spars for cracks, elongated holes, and
corrosion in accordance with Steps 1, 2, 4 through 6, 9, and 10 of
the Work Instructions--Inspection, Method 2 in Wipaire SL 253D.
(5) Within 5 days after each inspection required by paragraphs
(g)(1) and (4) of this AD or within 5 days after the effective date
of this AD, whichever occur later, report the following to the FAA
at the address in paragraph (j)(1) of this AD. Report this
information regardless of whether cracks are found.
(i) Model, engine configuration (with horsepower limits), and
propeller type;
(ii) Serial number and N number;
(iii) Total hours TIS on airframe;
(iv) Total hours TIS operated with floats, if known;
(v) STC configuration and total hours with STC installed;
(vi) Crack location (right or left, upper/lower caps inboard/
outboard hole);
(vii) Crack size;
(viii) Photos of cracks found, if available; and
(ix) Any additional operator/mechanic comments.
(h) Credit for Previous Actions
You may take credit for the initial inspection required by
paragraph (g)(1) of this AD if, before the effective date of this
AD, you complied with Wipaire, Inc. Service Letter 253, Revision A,
dated April 5, 2023; or Wipaire Service Letter 253, Revision B,
dated July 27, 2023.
(i) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Central Certification Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the Certification Branch, send it to the
attention of the person identified in paragraph (j)(1) of this AD
and email to: <a href="/cdn-cgi/l/email-protection#0c4d41434f4c6a6d6d226b637a"><span class="__cf_email__" data-cfemail="aeefe3e1edeec8cfcf80c9c1d8">[email protected]</span></a>.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(j) Related Information
(1) For more information about this AD, contact Tim Eichor,
Aviation Safety Engineer, Central Certification Branch, FAA, 1801 S.
Airport Road, Wichita, KS 67209; phone: (847) 294-7141; email:
<a href="/cdn-cgi/l/email-protection#44302d296a206a212d272c2b36042225256a232b32"><span class="__cf_email__" data-cfemail="384c5155165c165d515b50574a785e5959165f574e">[email protected]</span></a>.
(2) Material identified in this AD that is not incorporated by
reference is available at the address specified in paragraph (k)(3)
of this AD.
(k) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference of the material listed in this paragraph
under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this material as applicable to do the actions
required by this AD, unless the AD specifies otherwise.
(i) Wipaire, Inc. Service Letter 253, Revision D, dated July 3,
2024.
(ii) [Reserved]
(3) For Wipaire, Inc. material identified in this AD, contact
Wipaire, Inc., 1700 Henry Avenue, Fleming Field (KSGS), South St.
Paul, MN 55075; phone: (651) 451-1205; email:
<a href="/cdn-cgi/l/email-protection#3c5f494f485351594e4f594e4a555f597c005d1c544e595a01" http: wipaire.com">wipaire.com</a>">customerservice@<a href="http://wipaire.com">wipaire.com</a></a>; website: <a href="http://wipaire.com">wipaire.com</a>.
(4) You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 901 Locust, Kansas
City, MO 64106. For information on the availability of this material
at the FAA, call (817) 222-5110.
(5) You may view this material at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, visit <a href="http://www.archives.gov/federal-register/cfr/ibr-locations">www.archives.gov/federal-register/cfr/ibr-locations</a> or email <a href="/cdn-cgi/l/email-protection#a3c5d18dcacdd0d3c6c0d7cacccde3cdc2d1c28dc4ccd5"><span class="__cf_email__" data-cfemail="dbbda9f5b2b5a8abbeb8afb2b4b59bb5baa9baf5bcb4ad">[email protected]</span></a>.
Issued on August 14, 2024.
Victor Wicklund,
Deputy Director, Compliance & Airworthiness Division, Aircraft
Certification Service.
[FR Doc. 2024-18586 Filed 8-15-24; 11:15 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on August 20, 2024.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.