Proposed Rule2024-13278
Airworthiness Directives; Embraer S.A. Airplanes
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
June 20, 2024
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA proposes to adopt a new airworthiness directive (AD) for certain Embraer S.A. (Embraer) Model EMB-505 airplanes. This proposed AD was prompted by analysis of the left-hand (LH) refreshment center and LH forward cabinet that identified the need for installing structural reinforcements. This proposed AD would require installing structural reinforcements as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 89 Issue 119 (Thursday, June 20, 2024)</title>
</head>
<body><pre>
[Federal Register Volume 89, Number 119 (Thursday, June 20, 2024)]
[Proposed Rules]
[Pages 51853-51856]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2024-13278]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2024-1484; Project Identifier MCAI-2023-00968-A]
RIN 2120-AA64
Airworthiness Directives; Embraer S.A. Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for certain Embraer S.A. (Embraer) Model EMB-505 airplanes. This
proposed AD was prompted by analysis of the left-hand (LH) refreshment
center and LH forward cabinet that identified the need for installing
structural reinforcements. This proposed AD would require installing
structural reinforcements as specified in an Ag[ecirc]ncia Nacional de
Avia[ccedil][atilde]o Civil (ANAC) AD, which is proposed for
incorporation by reference. The FAA is proposing this AD to address the
unsafe condition on these products.
DATES: The FAA must receive comments on this NPRM by August 5, 2024.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
<bullet> Federal eRulemaking Portal: Go to <a href="http://regulations.gov">regulations.gov</a>. Follow
the instructions for submitting comments.
<bullet> Fax: (202) 493-2251.
<bullet> Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
<bullet> Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket: You may examine the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-1484; or in person at
[[Page 51854]]
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The AD docket contains this NPRM, the
mandatory continuing airworthiness information (MCAI), any comments
received, and other information. The street address for Docket
Operations is listed above.
Material Incorporated by Reference:
<bullet> For ANAC material contact ANAC, Continuing Airworthiness
Technical Branch (GTAC), Rua Doutor Orlando Feirabend Filho, 230--
Centro Empresarial Aquarius--Torre B--Andares 14 a 18, Parque
Residencial Aquarius, CEP 12.246-190--S[atilde]o Jos[eacute] dos
Campos--SP, Brazil; phone: 55 (12) 3203-6600; email: <a href="/cdn-cgi/l/email-protection#b5c5d4d6f589d495ddc7d0d388" http: anac.gov">anac.gov</a>.br">pac@<a href="http://anac.gov">anac.gov</a>.br</a>;
website: <a href="http://anac.gov">anac.gov</a>.br/en/. You may find this material on the ANAC
website at <a href="http://sistemas.anac.gov">sistemas.anac.gov</a>.br/certificacao/DA/DAE.asp. It is also
available at <a href="http://regulations.gov">regulations.gov</a> under Docket No. FAA-2024-1484.
<bullet> You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 901 Locust, Kansas City,
MO 64106. For information on the availability of this material at the
FAA, call (817) 222-5110.
FOR FURTHER INFORMATION CONTACT: Jim Rutherford, Aviation Safety
Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590;
phone: (816) 329-4165; email: <a href="/cdn-cgi/l/email-protection#a4cecdc98ad6d1d0ccc1d6c2cbd6c0e4c2c5c58ac3cbd2"><span class="__cf_email__" data-cfemail="3f555652114d4a4b575a4d59504d5b7f595e5e11585049">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under ADDRESSES. Include ``Docket No. FAA-2024-1484; Project Identifier
MCAI-2023-00968-A'' at the beginning of your comments. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing date and may amend
this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
<a href="http://regulations.gov">regulations.gov</a>, including any personal information you provide. The
agency will also post a report summarizing each substantive verbal
contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to Jim
Rutherford, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite
410, Westbury, NY 11590. Any commentary that the FAA receives which is
not specifically designated as CBI will be placed in the public docket
for this rulemaking.
Background
ANAC, which is the aviation authority for Brazil, has issued ANAC
AD 2023-07-01, effective August 10, 2023, as corrected by ANAC
Airworthiness Directive Errata, effective August 10, 2023 (ANAC AD
2023-07-01) (also referred to as the MCAI) to correct an unsafe
condition on certain serial-numbered Embraer Model EMB-505 airplanes.
The MCAI states that analysis identified that the LH refreshment center
and LH forward cabinet might not withstand the loads expected for
specific emergency landing conditions, which may cause the detachment
of mass items and cause injuries to the airplane occupants. In
addition, the MCAI includes errata to correct a printing error in the
original English version of the MCAI. The MCAI requires installing
structural reinforcements.
You may examine the MCAI in the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-1484.
Related Service Information Under 1 CFR Part 51
The FAA reviewed ANAC AD 2023-07-01, which specifies procedures for
installing structural reinforcements.
This service information is reasonably available because the
interested parties have access to it through their normal course of
business or by the means identified in ADDRESSES.
FAA's Determination
These products have been approved by the aviation authority of
another country and are approved for operation in the United States.
Pursuant to the FAA's bilateral agreement with this State of Design
Authority, it has notified the FAA of the unsafe condition described in
the MCAI described above. The FAA is issuing this NPRM after
determining that the unsafe condition described previously is likely to
exist or develop on other products of the same type design.
Proposed AD Requirements in This NPRM
This proposed AD would require accomplishing the actions specified
in ANAC AD 2023-07-01, except for any differences identified as
exceptions in the regulatory text of this proposed AD and except as
discussed under ``Differences Between this Proposed AD and the MCAI.''
Differences Between This Proposed AD and the MCAI
The service information specified in ANAC AD 2023-07-01 allows the
use of alternative or similar parts in place of the ones specified in
the kits, provided these alternative or similar parts are approved by
Embraer, but this proposed AD would require approval from either the
Manager, International Validation Branch, FAA; ANAC; or ANAC's
authorized Designee.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA developed a process to use some civil aviation
authority (CAA) ADs as the primary source of information for compliance
with requirements for corresponding FAA ADs. The FAA has been
coordinating this process with manufacturers and CAAs. As a result, the
FAA proposes to incorporate ANAC AD 2023-07-01 by reference in the FAA
final rule. This proposed AD would, therefore, require compliance with
ANAC AD 2023-07-01 in its entirety through that incorporation, except
for any differences identified as exceptions in the regulatory text of
this proposed AD. Service information required by ANAC AD 2023-07-01
will be available at <a href="http://regulations.gov">regulations.gov</a> under Docket No. FAA-2024-1484
after the FAA final rule is published.
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would
affect 229 airplanes of U.S. registry.
The FAA estimates the following costs to comply with this proposed
AD.
[[Page 51855]]
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Action Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
Install structural reinforcements..... 11 work-hours x $85 per $1,600 $2,535 $580,515
hour = $935.
----------------------------------------------------------------------------------------------------------------
The FAA has included all known costs in its cost estimate.
According to the manufacturer, however, some or all of the costs of
this proposed AD may be covered under warranty, thereby reducing the
cost impact on affected operators.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
Embraer S.A.: Docket No. FAA-2024-1484; Project Identifier MCAI-
2023-00968-A.
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive
(AD) by August 5, 2024.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Embraer S.A. Model EMB-505 airplanes,
certificated in any category, as identified in Ag[ecirc]ncia
Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD 2023-07-01,
effective August 10, 2023, as corrected by ANAC Airworthiness
Directive Errata, effective August 10, 2023 (ANAC AD 2023-07-01).
(d) Subject
Joint Aircraft System Component (JASC) Code 2500, Cabin
Equipment/Furnishings.
(e) Unsafe Condition
This AD was prompted by an analysis that the left-hand (LH)
refreshment center and LH forward cabinet might not withstand the
loads expected for specific emergency landing conditions. The FAA is
issuing this AD to address the possibility of detachment of mass
items during specific emergency landing conditions. The unsafe
condition, if not addressed, could result in injuries to the
airplane occupants.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Actions
Except as specified in paragraphs (h) and (i) of this AD: Comply
with all required actions and compliance times specified in, and in
accordance with, ANAC AD 2023-07-01.
(h) Exceptions to ANAC AD 2023-07-01
(1) Where ANAC AD 2023-07-01 refers to its effective date, this
AD requires using the effective date of this AD.
(2) Although the service information referenced in ANAC AD 2023-
07-01 allows the use of alternative or similar parts in place of the
ones specified in the kits provided, this AD requires that
alternative or similar parts be approved by the Manager,
International Validation Branch, FAA; ANAC; or ANAC's authorized
Designee. If approved by the ANAC Designee, the approval must
include the Designee's authorized signature.
(3) Where the service information referenced in ANAC AD 2023-07-
01 specifies to ``discard'' certain parts, for this AD replace that
text with ``remove from service.''
(4) This AD does not adopt paragraphs (c) and (d) of ANAC AD
2023-07-01.
(i) No Reporting Requirement
Although the service information referenced in ANAC AD 2023-07-
01 specifies to submit certain information to the manufacturer, this
AD does not include that requirement.
(j) Alternative Methods of Compliance (AMOCs)
The Manager, International Validation Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the International Validation Branch, mail
it to the address identified in paragraph (k) of this AD or email
to: <a href="/cdn-cgi/l/email-protection#91a8bcd0c7c2bcd0d8c3bca6a2a1bcd0dcded2d1f7f0f0bff6fee7"><span class="__cf_email__" data-cfemail="86bfabc7d0d5abc7cfd4abb1b5b6abc7cbc9c5c6e0e7e7a8e1e9f0">[email protected]</span></a>. If mailing information, also submit
information by email. Before using any approved AMOC, notify your
appropriate principal inspector, or lacking a principal inspector,
the manager of the local Flight Standards District Office/
certificate holding district office.
(k) Additional Information
For more information about this AD, contact Jim Rutherford,
Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410,
Westbury, NY 11590; phone: (816) 329-4165; email:
<a href="/cdn-cgi/l/email-protection#e2888b8fcc9097968a8790848d9086a2848383cc858d94"><span class="__cf_email__" data-cfemail="bed4d7d390cccbcad6dbccd8d1ccdafed8dfdf90d9d1c8">[email protected]</span></a>.
(l) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference of the service information listed in this
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless the AD specifies otherwise.
[[Page 51856]]
(i) Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC)
AD 2023-07-01, effective August 10, 2023, as corrected by ANAC
Airworthiness Directive Errata, effective August 10, 2023.
(ii) [Reserved]
(3) For ANAC AD 2023-07-01 contact ANAC, Continuing
Airworthiness Technical Branch (GTAC), Rua Doutor Orlando Feirabend
Filho, 230--Centro Empresarial Aquarius--Torre B--Andares 14 a 18,
Parque Residencial Aquarius, CEP 12.246-190--S[atilde]o Jos[eacute]
dos Campos--SP, Brazil; phone: 55 (12) 3203-6600; email:
<a href="/cdn-cgi/l/email-protection#91e1f0f2d1adf0b1f9e3f4f7ac" http: anac.gov">anac.gov</a>.br">pac@<a href="http://anac.gov">anac.gov</a>.br</a>; website: <a href="http://anac.gov">anac.gov</a>.br/en/. You may find this
material on the ANAC website at <a href="http://sistemas.anac.gov">sistemas.anac.gov</a>.br/certificacao/
DA/DAE.asp.
(4) You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 901 Locust, Kansas
City, MO 64106. For information on the availability of this material
at the FAA, call (817) 222-5110.
(5) You may view this material at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, visit <a href="http://www.archives.gov/federal-register/cfr/ibr-locations">www.archives.gov/federal-register/cfr/ibr-locations</a> or email <a href="/cdn-cgi/l/email-protection#1c7a6e3275726f6c797f687573725c727d6e7d327b736a"><span class="__cf_email__" data-cfemail="a3c5d18dcacdd0d3c6c0d7cacccde3cdc2d1c28dc4ccd5">[email protected]</span></a>.
Issued on June 11, 2024.
James D. Foltz,
Deputy Director, Compliance & Airworthiness Division, Aircraft
Certification Service.
[FR Doc. 2024-13278 Filed 6-18-24; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on June 20, 2024.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.