Proposed Rule2024-06994
Airworthiness Directives; Airbus SAS Airplanes
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
April 5, 2024
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA proposes to supersede Airworthiness Directive (AD) 2019-21-01, which applies to all Airbus SAS Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). AD 2019-21-01 requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2019-21-01, the FAA has determined that new or more restrictive airworthiness limitations are necessary. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 89 Issue 67 (Friday, April 5, 2024)</title>
</head>
<body><pre>
[Federal Register Volume 89, Number 67 (Friday, April 5, 2024)]
[Proposed Rules]
[Pages 23951-23954]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2024-06994]
========================================================================
Proposed Rules
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains notices to the public of
the proposed issuance of rules and regulations. The purpose of these
notices is to give interested persons an opportunity to participate in
the rule making prior to the adoption of the final rules.
========================================================================
Federal Register / Vol. 89, No. 67 / Friday, April 5, 2024 / Proposed
Rules
[[Page 23951]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2024-0992; Project Identifier MCAI-2024-00030-T]
RIN 2120-AA64
Airworthiness Directives; Airbus SAS Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD)
2019-21-01, which applies to all Airbus SAS Model A300 B4-600, B4-600R,
and F4-600R series airplanes, and Model A300 C4-605R Variant F
airplanes (collectively called Model A300-600 series airplanes). AD
2019-21-01 requires revising the existing maintenance or inspection
program, as applicable, to incorporate new or more restrictive
airworthiness limitations. Since the FAA issued AD 2019-21-01, the FAA
has determined that new or more restrictive airworthiness limitations
are necessary. This proposed AD would require revising the existing
maintenance or inspection program, as applicable, to incorporate new or
more restrictive airworthiness limitations, as specified in a European
Union Aviation Safety Agency (EASA) AD, which is proposed for
incorporation by reference (IBR). The FAA is proposing this AD to
address the unsafe condition on these products.
DATES: The FAA must receive comments on this proposed AD by May 20,
2024.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
<bullet> Federal eRulemaking Portal: Go to <a href="http://regulations.gov">regulations.gov</a>. Follow
the instructions for submitting comments.
<bullet> Fax: 202-493-2251.
<bullet> Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
<bullet> Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket: You may examine the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2024-0992; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this NPRM, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
street address for Docket Operations is listed above.
Material Incorporated by Reference:
<bullet> For EASA material that is proposed for IBR in this NPRM,
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone
+49 221 8999 000; email <a href="/cdn-cgi/l/email-protection#db9a9fa89bbebaa8baf5beaea9b4abbaf5beae"><span class="__cf_email__" data-cfemail="bafbfec9fadfdbc9db94dfcfc8d5cadb94dfcf">[email protected]</span></a>; website easa.europa.eu. You
may find this material on the EASA website at ad.easa.europa.eu.
<bullet> For Airbus SAS material, contact Airbus SAS, Airworthiness
Office--EAW, Rond-Point Emile Dewoitine No: 2, 31700 Blagnac Cedex,
France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; email
<a href="/cdn-cgi/l/email-protection#0f6e6c6c607a617b216e667d78607d7b67226a6e7c4f336e2f677d6a6932" http: airbus.com">airbus.com</a>">account.airworth-eas@<a href="http://airbus.com">airbus.com</a></a>; website <a href="http://airbus.com">airbus.com</a>.
<bullet> You may view this material that is incorporated by
reference at the FAA, Airworthiness Products Section, Operational
Safety Branch, 2200 South 216th St., Des Moines, WA. For information on
the availability of this material at the FAA, call 206-231-3195. It is
also available at <a href="http://regulations.gov">regulations.gov</a> under Docket No. FAA-2024-0992.
FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aviation Safety Engineer,
FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: 206-
231-3225; email: <a href="/cdn-cgi/l/email-protection#1b7f7a753569747f72757a5b7d7a7a357c746d"><span class="__cf_email__" data-cfemail="0d696c63237f626964636c4d6b6c6c236a627b">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under ADDRESSES. Include ``Docket No. FAA-2024-0992; Project Identifier
MCAI-2024-00030-T'' at the beginning of your comments. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing date and may amend
this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
<a href="http://regulations.gov">regulations.gov</a>, including any personal information you provide. The
agency will also post a report summarizing each substantive verbal
contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to Dan
Rodina, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410,
Westbury, NY 11590; phone: 206-231-3225; email: <a href="/cdn-cgi/l/email-protection#92f6f3fcbce0fdf6fbfcf3d2f4f3f3bcf5fde4"><span class="__cf_email__" data-cfemail="086c6966267a676c616669486e6969266f677e">[email protected]</span></a>. Any
commentary that the FAA receives that is not specifically designated as
CBI will be placed in the public docket for this rulemaking.
Background
The FAA issued AD 2019-21-01, Amendment 39-19767 (84 FR 56935,
October 24, 2019) (AD 2019-21-01), for all Airbus SAS Model A300 B4-
600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R
Variant F airplanes (collectively called Model A300-600 series
airplanes). AD 2019-21-01 was prompted by an MCAI originated by EASA,
which is the Technical Agent for the Member States of the European
Union. EASA issued AD 2019-0090, dated April 26, 2019
[[Page 23952]]
(EASA AD 2019-0090) (which corresponds to FAA AD 2019-21-01), to
correct an unsafe condition.
AD 2019-21-01 requires revising the existing maintenance or
inspection program, as applicable, to incorporate new or more
restrictive airworthiness limitations. The FAA issued AD 2019-21-01 to
address fatigue cracking, damage, and corrosion in principal structural
elements, which could result in reduced structural integrity of the
airplane. AD 2019-21-01 specifies that accomplishing the revision
required by that AD terminates all requirements of AD 2018-01-07,
Amendment 39-19148 (83 FR 2042, January 16, 2018) (AD 2018-01-07) and
AD 2018-19-33, Amendment 39-19434 (83 FR 48932, September 28, 2018) (AD
2018-19-33). This proposed AD would therefore continue to allow that
terminating action.
Actions Since AD 2019-21-01 Was Issued
Since the FAA issued AD 2019-21-01, EASA superseded AD 2019-0090
and issued EASA AD 2024-0009, dated January 9, 2024 (EASA AD 2024-0009)
(also referred to as the MCAI), for all Airbus SAS Model A300-600
airplanes. The MCAI states that new or more restrictive airworthiness
limitations have been developed.
The FAA is proposing this AD to address the unsafe condition on
these products. You may examine the MCAI in the AD docket at
<a href="http://regulations.gov">regulations.gov</a> under Docket No. FAA-2024-0992.
Related Service Information Under 1 CFR Part 51
The FAA reviewed EASA AD 2024-0009. This service information
specifies new or more restrictive airworthiness limitations for
airplane structures and safe life limits.
This proposed AD also would also require Airbus A300-600
Airworthiness Limitations Section (ALS), Part 2, ``Damage Tolerant
Airworthiness Limitation Items (DT-ALI),'' Revision 03, dated December
14, 2018, which the Director of the Federal Register approved for
incorporation by reference as of November 29, 2019 (84 FR 56935,
October 24, 2019).
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in ADDRESSES.
FAA's Determination
This product has been approved by the aviation authority of another
country and is approved for operation in the United States. Pursuant to
the FAA's bilateral agreement with this State of Design Authority, it
has notified the FAA of the unsafe condition described in the MCAI
referenced above. The FAA is issuing this NPRM after determining that
the unsafe condition described previously is likely to exist or develop
in other products of the same type design.
Proposed AD Requirements in This NPRM
This proposed AD would retain all requirements of AD 2019-21-01.
This proposed AD would also require revising the existing maintenance
or inspection program, as applicable, to incorporate additional new or
more restrictive airworthiness limitations, which are specified in EASA
AD 2024-0009 already described, as proposed for incorporation by
reference. Any differences with EASA AD 2024-0009 are identified as
exceptions in the regulatory text of this AD.
This proposed AD would require revisions to certain operator
maintenance documents to include new actions (e.g., inspections).
Compliance with these actions is required by 14 CFR 91.403(c). For
airplanes that have been previously modified, altered, or repaired in
the areas addressed by this proposed AD, the operator may not be able
to accomplish the actions described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must request
approval for an alternative method of compliance (AMOC) according to
paragraph (m)(1) of this proposed AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA developed a process to use some civil aviation
authority (CAA) ADs as the primary source of information for compliance
with requirements for corresponding FAA ADs. The FAA has been
coordinating this process with manufacturers and CAAs. As a result, the
FAA proposes to incorporate EASA AD 2024-0009 by reference in the FAA
final rule. This proposed AD would, therefore, require compliance with
EASA AD 2024-0009 through that incorporation, except for any
differences identified as exceptions in the regulatory text of this
proposed AD. Using common terms that are the same as the heading of a
particular section in EASA AD 2024-0009 does not mean that operators
need comply only with that section. For example, where the AD
requirement refers to ``all required actions and compliance times,''
compliance with this AD requirement is not limited to the section
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2024-
0009. Service information required by EASA AD 2024-0009 for compliance
will be available at <a href="http://regulations.gov">regulations.gov</a> by searching for and locating
Docket No. FAA-2024-0992 after the FAA final rule is published.
Airworthiness Limitation ADs Using the New Process
The FAA's process of incorporating by reference MCAI ADs as the
primary source of information for compliance with corresponding FAA ADs
has been limited to certain MCAI ADs (primarily those with service
bulletins as the primary source of information for accomplishing the
actions required by the FAA AD). However, the FAA is now expanding the
process to include MCAI ADs that require a change to airworthiness
limitation documents, such as airworthiness limitation sections.
For these ADs that incorporate by reference an MCAI AD that changes
airworthiness limitations, the FAA requirements are unchanged.
Operators must revise the existing maintenance or inspection program,
as applicable, to incorporate the information specified in the new
airworthiness limitation document. The airworthiness limitations must
be followed according to 14 CFR 91.403(c) and 91.409(e).
The previous format of the airworthiness limitation ADs included a
paragraph that specified that no alternative actions (e.g.,
inspections) or intervals may be used unless the actions and intervals
are approved as an AMOC in accordance with the procedures specified in
the AMOCs paragraph under ``Additional AD Provisions.'' This new format
includes a ``New Provisions for Alternative Actions and Intervals''
paragraph that does not specifically refer to AMOCs, but operators may
still request an AMOC to use an alternative action or interval.
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would
affect 120 airplanes of U.S. registry. The FAA estimates the following
costs to comply with this proposed AD:
The FAA has determined that revising the existing maintenance or
inspection program takes an average of 90 work-hours per operator,
although the agency recognizes that this number may vary from operator
to operator. Since operators incorporate maintenance or inspection
program changes for their affected fleet(s), the FAA has determined
that a per-operator estimate
[[Page 23953]]
is more accurate than a per-airplane estimate.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by:
0
a. Removing Airworthiness Directive (AD) AD 2019-21-01, Amendment 39-
19767 (84 FR 56935, October 24, 2019); and
0
b. Adding the following new AD:
Airbus SAS: Docket No. FAA-2024-0992; Project Identifier MCAI-2024-
00030-T.
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive
(AD) by May 20, 2024.
(b) Affected ADs
This AD replaces AD 2019-21-01, Amendment 39-19767 (84 FR 56935,
October 24, 2019) (AD 2019-21-01).
(c) Applicability
This AD applies to all Airbus SAS Model A300 B4-600, B4-600R,
and F4-600R series airplanes, and Model A300 C4-605R Variant F
airplanes (collectively called Model A300-600 series airplanes),
certificated in any category.
(d) Subject
Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.
(e) Unsafe Condition
This AD was prompted by a determination that new or more
restrictive airworthiness limitations are necessary. The FAA is
issuing this AD to address fatigue cracking, damage, and corrosion
in principal structural elements. The unsafe condition, if not
addressed, could result in reduced structural integrity of the
airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Retained Revision of the Existing Maintenance or Inspection
Program, With No Changes
This paragraph restates the requirements of paragraph (g) of AD
2019-21-01, with no changes. Within 90 days after November 29, 2019
(the effective date of AD 2019-21-01), revise the existing
maintenance or inspection program, as applicable, to incorporate the
information specified in Airbus A300-600 Airworthiness Limitations
Section (ALS), Part 2, ``Damage Tolerant Airworthiness Limitation
Items (DT-ALI),'' Revision 03, dated December 14, 2018. The initial
compliance time for doing the tasks is at the time specified in
Airbus A300-600 Airworthiness Limitations Section (ALS), Part 2,
``Damage Tolerant Airworthiness Limitation Items (DT-ALI),''
Revision 03, dated December 14, 2018, or within 90 days after
November 29, 2019 (the effective date of AD 2019-21-01), whichever
occurs later. Accomplishing the revision of the existing maintenance
or inspection program required by paragraph (i) of this AD
terminates the requirements of this paragraph.
(h) Retained Restrictions on Alternative Actions or Intervals With a
New Exception
This paragraph restates the requirements of paragraph (h) of AD
2019-21-01, with a new exception. Except as required by paragraph
(i) of this AD: After the existing maintenance or inspection program
has been revised as required by paragraph (g) of this AD, no
alternative actions (e.g., inspections) or intervals may be used
unless the actions and intervals are approved as an alternative
method of compliance (AMOC) in accordance with the procedures
specified in paragraph (m)(1) of this AD.
(i) New Revision of the Existing Maintenance or Inspection Program
Except as specified in paragraph (j) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, EASA AD 2024-0009, dated January 9, 2024 (EASA AD
2024-0009). Accomplishing the revision of the existing maintenance
or inspection program required by this paragraph terminates the
requirements of paragraph (g) of this AD.
(j) Exceptions to EASA AD 2024-0009
(1) This AD does not adopt the requirements specified in
paragraphs (1) and (2) of EASA AD 2024-0009.
(2) Paragraph (4) of EASA AD 2024-0009 specifies revising ``the
approved AMP,'' within 12 months after its effective date, but this
AD requires revising the existing maintenance or inspection program,
as applicable, within 90 days after the effective date of this AD.
(3) The initial compliance time for doing the tasks specified in
paragraph (4) of EASA AD 2024-0009 is at the applicable
``limitations'' and ``associated thresholds'' as incorporated by the
requirements of paragraph (4) of EASA AD 2024-0009, or within 90
days after the effective date of this AD, whichever occurs later.
(4) This AD does not adopt the provisions specified in
paragraphs (5) and (6) of EASA AD 2024-0009.
(5) This AD does not adopt the ``Remarks'' section of EASA AD
2024-0009.
(k) New Provisions for Alternative Actions and Intervals
After the existing maintenance or inspection program has been
revised as required by paragraph (i) of this AD, no alternative
actions (e.g., inspections) and intervals are allowed unless they
are approved as specified in the provisions of the ``Ref.
Publications'' section of EASA AD 2024-0009.
(l) Terminating Action for AD 2019-21-01
Accomplishing the actions required by this AD terminates all
requirements of AD 2019-21-01.
(m) Additional AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Validation Branch, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19.
[[Page 23954]]
In accordance with 14 CFR 39.19, send your request to your principal
inspector or responsible Flight Standards Office, as appropriate. If
sending information directly to the manager of the International
Validation Branch, mail it to the address identified in paragraph
(n) of this AD. Information may be emailed to: <a href="/cdn-cgi/l/email-protection#7a43573b2c29573b3328574d494a573b3735393a1c1b1b541d150c"><span class="__cf_email__" data-cfemail="5a63771b0c09771b1308776d696a771b1715191a3c3b3b743d352c">[email protected]</span></a>. Before using any approved AMOC, notify your
appropriate principal inspector, or lacking a principal inspector,
the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, International
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design
Organization Approval (DOA). If approved by the DOA, the approval
must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by
paragraph (m)(2) of this AD, if any service information contains
procedures or tests that are identified as RC, those procedures and
tests must be done to comply with this AD; any procedures or tests
that are not identified as RC are recommended. Those procedures and
tests that are not identified as RC may be deviated from using
accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC, provided
the procedures and tests identified as RC can be done and the
airplane can be put back in an airworthy condition. Any
substitutions or changes to procedures or tests identified as RC
require approval of an AMOC.
(n) Additional Information
For more information about this AD, contact Dan Rodina, Aviation
Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY
11590; phone: 206-231-3225; email: <a href="/cdn-cgi/l/email-protection#e88c8986c69a878c818689a88e8989c68f879e"><span class="__cf_email__" data-cfemail="9efafff0b0ecf1faf7f0ffdef8ffffb0f9f1e8">[email protected]</span></a>.
(o) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless this AD specifies otherwise.
(3) The following service information was approved for IBR on
[DATE 35 DAYS AFTER PUBLICATION OF THE FINAL RULE].
(i) European Union Aviation Safety Agency (EASA) AD 2024-0009,
dated January 9, 2024.
(ii) [Reserved]
(4) The following service information was approved for IBR on
November 29, 2019 (84 FR 56935, October 24, 2019).
(i) Airbus A300-600 Airworthiness Limitations Section (ALS),
Part 2, ``Damage Tolerant Airworthiness Limitation Items (DT-ALI),''
Revision 03, dated December 14, 2018.
(ii) [Reserved]
(5) For EASA AD 2024-0009, contact EASA, Konrad-Adenauer-Ufer 3,
50668 Cologne, Germany; telephone +49 221 8999 000; email
<a href="/cdn-cgi/l/email-protection#d09194a390b5b1a3b1feb5a5a2bfa0b1feb5a5"><span class="__cf_email__" data-cfemail="3b7a7f487b5e5a485a155e4e49544b5a155e4e">[email protected]</span></a>; website easa.europa.eu. You may find this EASA
AD on the EASA website at ad.easa.europa.eu.
(6) For Airbus SAS material, contact Airbus SAS, Airworthiness
Office--EAW, Rond-Point Emile Dewoitine No: 2, 31700 Blagnac Cedex,
France; telephone +33 5 61 93 36 96; fax +33 5 61 93 44 51; email
<a href="/cdn-cgi/l/email-protection#472624242832293369262e35302835332f6a222634077b26672f3522217a" http: airbus.com">airbus.com</a>">account.airworth-eas@<a href="http://airbus.com">airbus.com</a></a>; website <a href="http://airbus.com">airbus.com</a>.
(7) You may view this material that is incorporated by reference
at the FAA, Airworthiness Products Section, Operational Safety
Branch, 2200 South 216th St., Des Moines, WA. For information on the
availability of this material at the FAA, call 206-231-3195.
(8) You may view this material at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, visit <a href="http://www.archives.gov/federal-register/cfr/ibr-locations">www.archives.gov/federal-register/cfr/ibr-locations</a>, or email <a href="/cdn-cgi/l/email-protection#3f594d1156514c4f5a5c4b5650517f515e4d5e11585049"><span class="__cf_email__" data-cfemail="670115490e0914170204130e0809270906150649000811">[email protected]</span></a>.
Issued on March 28, 2024.
Victor Wicklund,
Deputy Director, Compliance & Airworthiness Division, Aircraft
Certification Service.
[FR Doc. 2024-06994 Filed 4-4-24; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on April 5, 2024.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.