Rule2023-10620
Airworthiness Directives; Airbus Helicopters
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
May 18, 2023
Effective
June 22, 2023
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters (Airbus) Model AS332C, AS332C1, AS332L, AS332L1, AS332L2, and EC225LP helicopters. This AD is prompted by modifications developed by Airbus to address a report of an emergency exit window that required excessive pushing force to jettison. This AD requires removing skived polytetrafluoroethylene tape (PTFE tape) (if installed) and replacing certain polychloroprene seals with silicone seals, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD also prohibits installing a jettisonable window unless the actions required by this AD have been accomplished. The FAA is issuing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 88 Issue 96 (Thursday, May 18, 2023)</title>
</head>
<body><pre>
[Federal Register Volume 88, Number 96 (Thursday, May 18, 2023)]
[Rules and Regulations]
[Pages 31604-31607]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2023-10620]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2023-0160; Project Identifier MCAI-2022-01047-R;
Amendment 39-22421; AD 2023-08-06]
RIN 2120-AA64
Airworthiness Directives; Airbus Helicopters
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for
certain Airbus Helicopters (Airbus) Model AS332C, AS332C1, AS332L,
AS332L1, AS332L2, and EC225LP helicopters. This AD is prompted by
modifications developed by Airbus to address a report of an emergency
exit window that required excessive pushing force to jettison. This AD
requires removing skived polytetrafluoroethylene tape (PTFE tape) (if
installed) and replacing certain polychloroprene seals with silicone
seals, as specified in a European Union Aviation Safety Agency (EASA)
AD, which is incorporated by reference. This AD also prohibits
installing a jettisonable window unless the actions required by this AD
have been accomplished. The FAA is issuing this AD to address the
unsafe condition on these products.
DATES: This AD is effective June 22, 2023.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of June 22,
2023.
ADDRESSES:
AD Docket: You may examine the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2023-0160; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this final rule, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
address for Docket Operations is U.S. Department of Transportation,
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200
New Jersey Avenue SE, Washington, DC 20590.
Material Incorporated by Reference:
<bullet> For EASA material that is incorporated by reference in
this final rule, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne,
Germany; telephone +49 221 8999 000; email <a href="/cdn-cgi/l/email-protection#2061645360454153410e4555524f50410e4555"><span class="__cf_email__" data-cfemail="0a4b4e794a6f6b796b246f7f78657a6b246f7f">[email protected]</span></a>; internet
[[Page 31605]]
easa.europa.eu. You may find the EASA material on the EASA website at
ad.easa.europa.eu.
<bullet> You may view this service information at the FAA, Office
of the Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room
6N-321, Fort Worth, TX 76177. For information on the availability of
this material at the FAA, call (817) 222-5110. It is also available at
<a href="http://regulations.gov">regulations.gov</a> under Docket No. FAA-2023-0160.
FOR FURTHER INFORMATION CONTACT: Matthew Fuller, AD Program Manager,
General Aviation & Rotorcraft Unit, Airworthiness Products Section,
Operational Safety Branch, FAA, 10101 Hillwood Pkwy., Fort Worth, TX
76177; telephone (817) 222-5110; email <a href="/cdn-cgi/l/email-protection#a6cbc7d2d2cec3d188c0d3cacac3d4e6c0c7c788c1c9d0"><span class="__cf_email__" data-cfemail="7914180d0d111c0e571f0c15151c0b391f1818571e160f">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Background
EASA, which is the Technical Agent for the Member States of the
European Union, has issued a series of ADs, the most recent previously
being EASA AD 2021-0012, dated January 11, 2021 (EASA AD 2021-0012), to
correct an unsafe condition for certain Airbus Model AS332C, AS332C1,
AS332L, AS332L1, AS332L2, and EC225LP helicopters.
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 by adding an AD that would apply to Airbus Model AS332C,
AS332C1, AS332L, AS332L1, AS332L2, and EC225LP helicopters. The NPRM
published in the Federal Register on February 8, 2023 (88 FR 8238). The
NPRM was prompted by modifications developed by Airbus to address a
report of an emergency exit window that required excessive pushing
force to jettison. The NPRM proposed to require accomplishing the
actions specified in EASA AD 2021-0012, described previously, as
incorporated by reference, except for any differences identified as
exceptions in the regulatory text of this AD and except as discussed
under ``Differences Between this AD and EASA AD 2021-0012. The FAA is
issuing this AD to address the unsafe condition on these products.
After the NPRM was issued, EASA AD 2021-0012 was revised with EASA
AD 2021-0012R1, dated February 25, 2023 (EASA AD 2021-0012R1) to
include an alternate method to modify the window jettisoning system.
Because operators may request an alternate method of compliance for
accomplishing the requirements of this AD, the FAA is not incorporating
by reference EASA AD 2021-0012R1 but is incorporating by reference EASA
AD 2021-0012 as proposed in the NPRM.
You may examine the MCAI in the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2023-0160.
Discussion of Final Airworthiness Directive
Comments
The FAA received no comments on the NPRM or on the determination of
the costs.
Conclusion
These products have been approved by the aviation authority of
another country and are approved for operation in the United States.
Pursuant to the FAA's bilateral agreement with this State of Design
Authority, it has notified the FAA of the unsafe condition described in
the MCAI referenced above. The FAA reviewed the relevant data and
determined that air safety requires adopting this AD as proposed.
Accordingly, the FAA is issuing this AD to address the unsafe condition
on these products.
Related Service Information Under 1 CFR Part 51
EASA AD 2021-0012 requires modifying the windows jettisoning
system.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in ADDRESSES.
Other Related Service Information
The FAA reviewed Airbus Alert Service Bulletin (ASB) No. AS332-
56.00.16, Revision 0, dated February 10, 2020, Airbus ASB No. AS332-
56.00.18, Revision 0, dated September 23, 2020, Airbus ASB No. AS332-
56.00.20, Revision 0, dated September 23, 2020, Airbus ASB No. AS332-
56.00.21, Revision 0, dated September 23, 2020, Airbus ASB No. AS332-
56.90.14, Revision 0, dated April 10, 2019, Airbus ASB No. EC225-
56A013, Revision 1, dated February 10, 2020, Airbus ASB No. EC225-
56A015, Revision 0, dated February 10, 2020, Airbus ASB No. EC225-
56A016, Revision 0, dated February 10, 2020, and Airbus ASB No. EC225-
56A017, Revision 0, dated February 10, 2020. This service information
specifies procedures for modifying the windows jettisoning system.
Depending on your helicopter configuration, the service information
specifies procedures for removing PTFE tape (if installed), discarding
certain internal seal keys and external extraction tapes, installing
plugs on certain snap fasteners, removing certain emergency exit
installation indications, measuring the thickness of certain windows,
replacing certain windows, measuring the clearance between certain
windows and the airframe, modifying certain assemblies of the external
extraction tape with its associated marking (if necessary), and
replacing certain polychloroprene seals with silicone seals.
The FAA also reviewed EASA AD 2021-0012R1, which requires modifying
the windows jettisoning system and provides an alternate method for
modifying the window jettisoning system than that required in EASA AD
2021-0012.
Differences Between This AD and EASA AD 2021-0012
EASA AD 2021-0012 requires compliance within 250 flight hours or 6
months for certain helicopters not operated over water and within 110
flight hours or 6 months for certain other helicopters operated over
water. EASA AD 2021-0012 also requires compliance within 25 months for
all other affected helicopters. However, this AD requires compliance
within 110 hours time-in-service for all helicopters.
Where the service information referenced in EASA AD 2021-0012
specifies discarding parts, this AD requires removing those parts from
service. The service information referenced in EASA AD 2021-0012
specifies contacting Airbus Helicopter to obtain a technical solution,
whereas this AD requires repair done in accordance with a method
approved by the FAA, EASA, or Airbus Helicopters' EASA Design
Organization Approval. The service information referenced in EASA AD
2021-0012 specifies using a video, whereas this AD does not.
This AD also prohibits installing a jettisonable window unless the
actions required by this AD have been accomplished, whereas EASA AD
2021-0012 does not require any installation limitations.
Costs of Compliance
The FAA estimates that this AD affects 39 helicopters of U.S.
Registry. Labor costs are estimated at $85 per work-hour. Based on
these numbers, the FAA estimates the following costs to comply with
this AD.
Modifying a window takes about 2 work-hours and parts cost about
$220 for an estimated cost of $390 per window. There may be up to
twelve affected windows on a helicopter for an estimated cost of up to
$4,680 per helicopter and up to $182,520 for the U.S. fleet.
[[Page 31606]]
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
2023-08-06 Airbus Helicopters: Amendment 39-22421; Docket No. FAA-
2023-0160; Project Identifier MCAI-2022-01047-R.
(a) Effective Date
This airworthiness directive (AD) is effective June 22, 2023.
(b) Affected ADs
Accomplishing the actions required by this AD terminates all
requirements of AD 2020-20-08, Amendment 39-21264 (85 FR 70955,
November 6, 2020).
(c) Applicability
This AD applies to Airbus Helicopters Model AS332C, AS332C1,
AS332L, AS332L1, AS332L2, and EC225LP helicopters, certificated in
any category, as identified in European Union Aviation Safety Agency
(EASA) AD 2021-0012, dated January 11, 2021 (EASA AD 2021-0012).
(d) Subject
Joint Aircraft System Component (JASC) Code: 5220, Emergency
Exits.
(e) Unsafe Condition
This AD was prompted by a report of an emergency exit window
that required excessive pushing force to jettison caused by friction
between the jettisonable window and the airframe. The FAA is issuing
this AD to prevent excessive friction between the jettisonable cabin
window and the airframe. The unsafe condition, if not addressed,
could prevent the window from jettisoning, subsequently affecting
the evacuation of passengers during an emergency situation.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
(1) Except as specified in paragraphs (h) and (i) of this AD:
Comply with all required actions and compliance times specified in,
and in accordance with, EASA AD 2021-0012.
(2) As of the effective date of this AD, do not install a
jettisonable window on any helicopter unless the actions required by
this AD have been accomplished.
(h) Exceptions to EASA AD 2021-0012
(1) Where EASA AD 2021-0012 requires compliance in terms of
flight hours, this AD requires using hours time-in-service.
(2) Where EASA AD 2021-0012 refers to its effective date, the
effective date of EASA AD 2019-0107, dated May 16, 2019, and the
effective date of EASA AD 2020-0061, dated March 17, 2020, this AD
requires using the effective date of this AD.
(3) Where paragraph (1) of EASA AD 2021-0012 specifies
compliance within 250 flight hours or 6 months for helicopters not
operated over water and within 110 flight hours or 6 months for
helicopters operated over water, this AD requires compliance within
110 hours time-in-service (TIS) for Group 1 and Group 2 helicopters,
as defined in EASA AD 2021-0012.
(4) Where paragraph (2) of EASA AD 2021-0012 specifies
compliance within 25 months, this AD requires compliance within 110
hours TIS.
(5) Where the service information referenced in EASA AD 2021-
0012 specifies discarding parts, this AD requires removing those
parts from service.
(6) Where the service information referenced in EASA AD 2021-
0012 specifies contacting Airbus Helicopters to obtain a technical
solution, this AD requires repair done in accordance with a method
approved by the Manager, General Aviation & Rotorcraft Section,
International Validation Branch, FAA; or EASA; or Airbus
Helicopters' EASA Design Organization Approval (DOA). If approved by
the DOA, the approval must include the DOA-authorized signature.
(7) Where the service information referenced in EASA AD 2021-
0012 specifies to use tooling, this AD allows the use of equivalent
tooling.
(8) Where the service information referenced in EASA AD 2021-
0012 specifies using a video, this AD does not require using the
video.
(9) Paragraph (3) of EASA AD 2021-0012 does not apply to this
AD. Refer to paragraph (b) of this AD for affected FAA AD
information.
(10) This AD does not adopt the Remarks paragraph of EASA AD
2021-0012.
(i) No Reporting Requirement
Although the service information referenced in EASA AD 2021-0012
specifies to submit certain information to the manufacturer, this AD
does not include that requirement.
(j) Special Flight Permit
Special flight permits are prohibited for flights over water
with passengers on board.
(k) Alternative Methods of Compliance (AMOCs)
(1) The Manager, International Validation Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the International Validation Branch, send
it to the attention of the person identified in paragraph (l)(2) of
this AD. Information may be emailed to: <a href="/cdn-cgi/l/email-protection#1c25315d4a4f315d554e312b2f2c315d51535f5c7a7d7d327b736a"><span class="__cf_email__" data-cfemail="122b3f5344413f535b403f2521223f535f5d51527473733c757d64">[email protected]</span></a>.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(l) Additional Information
(1) For Airbus Helicopters service information identified in
this AD, contact Airbus Helicopters, Ala Ramaden, 2701 N Forum
Drive, Grand Prairie, TX 75052, United States; phone: (972) 641-
0000; website: <a href="http://airbus.com/helicopters/services/technical-support.html">airbus.com/helicopters/services/technical-support.html</a>.
(2) For more information about this AD, contact Matthew Fuller,
AD Program Manager, General Aviation & Rotorcraft Unit,
Airworthiness Products Section, Operational
[[Page 31607]]
Safety Branch, FAA, 10101 Hillwood Pkwy., Fort Worth, TX 76177;
telephone (817) 222-5110; email <a href="/cdn-cgi/l/email-protection#b3ded2c7c7dbd6c49dd5c6dfdfd6c1f3d5d2d29dd4dcc5"><span class="__cf_email__" data-cfemail="c3aea2b7b7aba6b4eda5b6afafa6b183a5a2a2eda4acb5">[email protected]</span></a>.
(m) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference of the service information listed in this
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless the AD specifies otherwise.
(i) European Union Aviation Safety Agency (EASA) AD 2021-0012,
dated January 11, 2021.
(ii) [Reserved]
(3) For EASA AD 2021-0012, contact EASA, Konrad-Adenauer-Ufer 3,
50668 Cologne, Germany; phone: +49 221 8999 000; email:
<a href="/cdn-cgi/l/email-protection#1b5a5f685b7e7a687a357e6e69746b7a357e6e"><span class="__cf_email__" data-cfemail="f7b6b384b792968496d9928285988796d99282">[email protected]</span></a>. You may find this material on the EASA website
at ad.easa.europa.eu.
(4) You may view this service information at FAA, Office of the
Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-
321, Fort Worth, TX 76177. For information on the availability of
this material at the FAA, call (817) 222-5110.
(5) You may view this service information that is incorporated
by reference at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, email: <a href="/cdn-cgi/l/email-protection#6d0b1f4304031e1d080e190402032d030c1f0c430a021b"><span class="__cf_email__" data-cfemail="fe988cd097908d8e9b9d8a979190be909f8c9fd0999188">[email protected]</span></a>, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">www.archives.gov/federal-register/cfr/ibr-locations.html</a>.
Issued on April 19, 2023.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft
Certification Service.
[FR Doc. 2023-10620 Filed 5-17-23; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on May 18, 2023.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.