Rule2023-01285
Airworthiness Directives; Stemme AG Gliders
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
January 25, 2023
Effective
March 1, 2023
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA is superseding Airworthiness Directive (AD) 2022-01-09 for certain Stemme AG Model Stemme S 10-VT and Model Stemme S 12 gliders. AD 2022-01-09 required removing the affected freewheel clutch from service and prohibited the installation of affected parts. Since the FAA issued AD 2022-01-09, the European Union Aviation Safety Agency (EASA) superseded its mandatory continuing airworthiness information (MCAI) to amend the definition of an affected part. This AD retains the requirements of AD 2022-01-09 for removing the affected freewheel clutch from service and continues to prohibit the installation of an affected part, and amends the definition of an affected part and clarifies the part installation prohibition. The FAA is issuing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 88 Issue 16 (Wednesday, January 25, 2023)</title>
</head>
<body><pre>
[Federal Register Volume 88, Number 16 (Wednesday, January 25, 2023)]
[Rules and Regulations]
[Pages 4721-4722]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2023-01285]
========================================================================
Rules and Regulations
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains regulatory documents
having general applicability and legal effect, most of which are keyed
to and codified in the Code of Federal Regulations, which is published
under 50 titles pursuant to 44 U.S.C. 1510.
The Code of Federal Regulations is sold by the Superintendent of Documents.
========================================================================
Federal Register / Vol. 88, No. 16 / Wednesday, January 25, 2023 /
Rules and Regulations
[[Page 4721]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2022-1421; Project Identifier MCAI-2022-01088-G;
Amendment 39-22310; AD 2023-02-03]
RIN 2120-AA64
Airworthiness Directives; Stemme AG Gliders
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2022-01-09
for certain Stemme AG Model Stemme S 10-VT and Model Stemme S 12
gliders. AD 2022-01-09 required removing the affected freewheel clutch
from service and prohibited the installation of affected parts. Since
the FAA issued AD 2022-01-09, the European Union Aviation Safety Agency
(EASA) superseded its mandatory continuing airworthiness information
(MCAI) to amend the definition of an affected part. This AD retains the
requirements of AD 2022-01-09 for removing the affected freewheel
clutch from service and continues to prohibit the installation of an
affected part, and amends the definition of an affected part and
clarifies the part installation prohibition. The FAA is issuing this AD
to address the unsafe condition on these products.
DATES: This AD is effective March 1, 2023.
ADDRESSES:
AD Docket: You may examine the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2022-1421; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this final rule, any comments received, the MCAI, and
other information. The address for Docket Operations is U.S. Department
of Transportation, Docket Operations, M-30, West Building Ground Floor,
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Jim Rutherford, Aviation Safety
Engineer, General Aviation & Rotorcraft Section, International
Validation Branch, FAA, 901 Locust, Room 301, Kansas City, MO 64106;
phone: (816) 329-4165; email: <a href="/cdn-cgi/l/email-protection#7d171410530f080915180f1b120f193d1b1c1c531a120b"><span class="__cf_email__" data-cfemail="69030004471b1c1d010c1b0f061b0d290f0808470e061f">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Background
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to supersede AD 2022-01-09, Amendment 39-21897 (87 FR 1666,
January 12, 2022) (AD 2022-01-09). AD 2022-01-09 applied to all Stemme
AG Model Stemme S 10-VT and Model Stemme S 12 gliders with a freewheel
clutch part number (P/N) 12AK with a serial number starting with ``12-
'' installed. AD 2022-01-09 required removing the affected freewheel
clutch from service and prohibited installing an affected part on any
glider. The FAA issued AD 2022-01-09 to address unintended slipping of
the freewheel clutch with overheating (burnishing) of the friction pads
inside of the clutch, which if not addressed, could result in a loss of
thrust and consequent loss of glider control.
The NPRM published in the Federal Register on November 18, 2022 (87
FR 69220). The NPRM was prompted by EASA AD 2021-0278R1, dated August
11, 2022 (referred to after this as ``the MCAI''), issued by EASA,
which is the Technical Agent for the Member States of the European
Union. The MCAI states that the definition of affected part is amended
to exclude certain modified and re-identified freewheel clutches. You
may examine the MCAI in the AD docket at <a href="http://regulations.gov">regulations.gov</a> under Docket
No. FAA-2022-1421.
In the NPRM, the FAA proposed to retain the requirements of AD
2022-01-09 for removing the affected freewheel clutch from service and
continue to prohibit the installation of an affected part, and amend
the definition of an affected part and clarify the part installation
prohibition.
Discussion of Final Airworthiness Directive
Comments
The FAA received a comment from one commenter. An individual
supported the NPRM without change.
Conclusion
These products have been approved by the aviation authority of
another country and are approved for operation in the United States.
Pursuant to the FAA's bilateral agreement with this State of Design
Authority, it has notified the FAA of the unsafe condition described in
the MCAI referenced above. The FAA reviewed the relevant data,
considered the comment received, and determined that air safety
requires adopting the AD as proposed. Accordingly, the FAA is issuing
this AD to address the unsafe condition on these products. Except for
minor editorial changes, including correcting a typographical error in
the Required Action and Compliance paragraph, this AD is adopted as
proposed in the NPRM.
Costs of Compliance
The FAA estimates that this AD affects 63 gliders of U.S. registry.
The FAA estimates the following costs to comply with this AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Action Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
Remove freewheel clutch from service.. 4 work-hours x $85 per $500 $840 $52,920
hour = $340.
----------------------------------------------------------------------------------------------------------------
[[Page 4722]]
The new requirements of this AD add no additional economic burden
over that already required by AD 2022-01-09.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA has determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by:
0
a. Removing Airworthiness Directive 2022-01-09, Amendment 39-21897 (87
FR 1666, January 12, 2022); and
0
b. Adding the following new airworthiness directive:
2023-02-03 Stemme AG: Amendment 39-22310; Docket No. FAA-2022-1421;
Project Identifier MCAI-2022-01088-G.
(a) Effective Date
This airworthiness directive (AD) is effective March 1, 2023.
(b) Affected ADs
This AD replaces AD 2022-01-09, Amendment 39-21897 (87 FR 1666,
January 12, 2022).
(c) Applicability
This AD applies to Stemme AG Model Stemme S 10-VT and Model
Stemme S 12 gliders, all serial numbers, certificated in any
category, with a freewheel clutch having part number 12AK with a
serial number starting with ``12-'' installed, except those which
have been modified by following the instructions of Stemme Service
Bulletin Doc. No. P062-980058, Revision 02, dated April 19, 2022,
and have been re-identified with ``/M'' at the end of the serial
number.
(d) Subject
Joint Aircraft System Component (JASC) Code 7100, Powerplant
System.
(e) Unsafe Condition
This AD was prompted by mandatory continuing airworthiness
information (MCAI) originated by an aviation authority of another
country to identify and correct an unsafe condition on an aviation
product. The MCAI identifies the unsafe condition as unintended
slipping of the freewheel clutch with overheating (burnishing) of
the friction pads inside of the clutch. The FAA is issuing this AD
to ensure removal of the affected freewheel clutch from service. The
unsafe condition, if not addressed, could result in a loss of thrust
and consequent loss of glider control.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Action and Compliance
(1) Before further flight after the effective date of this AD,
remove the freewheel clutch from service.
(2) As of the effective date of this AD, do not install a
freewheel clutch part number 12AK with a serial number starting with
``12-'' on any glider, unless it has been modified by following the
instructions of Stemme Service Bulletin Doc. No. P062-980058,
Revision 02, dated April 19, 2022, and has been re-identified with
``/M'' at the end of the serial number.
(h) Alternative Methods of Compliance (AMOCs)
The Manager, International Validation Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in Sec. 39.19. In accordance with Sec. 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the International Validation Branch, mail
it to the address identified in paragraph (i)(2) of this AD or email
to: <a href="/cdn-cgi/l/email-protection#6f56422e393c422e263d42585c5f422e22202c2f090e0e41080019"><span class="__cf_email__" data-cfemail="675e4a2631344a262e354a5054574a262a28242701060649000811">[email protected]</span></a>. If mailing information, also submit
information by email. Before using any approved AMOC, notify your
appropriate principal inspector, or lacking a principal inspector,
the manager of the local flight standards district office/
certificate holding district office. AMOCs approved for AD 2022-01-
09 are approved as AMOCs for the corresponding provisions of this
AD.
(i) Additional Information
(1) Refer to European Union Aviation Safety Agency (EASA) AD
2021-0278R1, dated August 11, 2022, for related information. This
EASA AD may be found in the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2022-1421.
(2) For more information about this AD, contact Jim Rutherford,
Aviation Safety Engineer, General Aviation & Rotorcraft Section,
International Validation Branch, FAA, 901 Locust, Room 301, Kansas
City, MO 64106; phone: (816) 329-4165; email:
<a href="/cdn-cgi/l/email-protection#3d575450134f484955584f5b524f597d5b5c5c135a524b"><span class="__cf_email__" data-cfemail="6d070400431f181905081f0b021f092d0b0c0c430a021b">[email protected]</span></a>.
(3) For service information identified in this AD that is not
incorporated by reference, contact Stemme AG, Flugplatzstrasse F2,
Nr. 6-7, D-15344 Strausberg, Germany; phone: +49 (0) 3341 3612-0;
fax: +49 (0) 3341 3612-30; email: <a href="/cdn-cgi/l/email-protection#3d5c544f4a524f49555453584e4e7d4e4958505058135958"><span class="__cf_email__" data-cfemail="5c3d352e2b332e28343532392f2f1c2f2839313139723839">[email protected]</span></a>; website:
<a href="http://stemme.com">stemme.com</a>. You may view this referenced service information at the
FAA, Airworthiness Products Section, Operational Safety Branch, 901
Locust, Kansas City, MO 64106. For information on the availability
of this material at the FAA, call (817) 222-5110.
(j) Material Incorporated by Reference
None.
Issued on January 19, 2023.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft
Certification Service.
[FR Doc. 2023-01285 Filed 1-24-23; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on January 25, 2023.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.