Rule2022-27403
Airworthiness Directives; Airbus SAS Airplanes
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
December 19, 2022
Effective
January 3, 2023
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-1041 airplanes. This AD was prompted by a report of a loud noise and vibration in the belly fairing (BF) access panel above the wings. This AD requires a one-time detailed inspection of the BF access panels and, depending on findings, accomplishment of applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference (IBR). The FAA is issuing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 87 Issue 242 (Monday, December 19, 2022)</title>
</head>
<body><pre>
[Federal Register Volume 87, Number 242 (Monday, December 19, 2022)]
[Rules and Regulations]
[Pages 77502-77505]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2022-27403]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2022-1576; Project Identifier MCAI-2022-01183-T;
Amendment 39-22277; AD 2022-25-21]
RIN 2120-AA64
Airworthiness Directives; Airbus SAS Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for
certain Airbus SAS Model A350-1041 airplanes. This AD was prompted by a
report of a loud noise and vibration in the belly fairing (BF) access
panel above the wings. This AD requires a one-time detailed inspection
of the BF access panels and, depending on findings, accomplishment of
applicable corrective actions, as specified in a European Union
Aviation Safety Agency (EASA) AD, which is incorporated by reference
(IBR). The FAA is issuing this AD to address the unsafe condition on
these products.
DATES: This AD becomes effective January 3, 2023.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in this AD as of January 3,
2023.
The FAA must receive comments on this AD by February 2, 2023.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
<bullet> Federal eRulemaking Portal: Go to <a href="http://regulations.gov">regulations.gov</a>. Follow
the instructions for submitting comments.
<bullet> Fax: 202-493-2251.
<bullet> Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
<bullet> Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket: You may examine the AD docket at <a href="http://regulations.gov">regulations.gov</a> under
Docket No. FAA-2022-1576; or in person at Docket Operations between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains this final rule, the mandatory continuing airworthiness
information (MCAI), any comments received, and other information. The
street address for Docket Operations is listed above.
Material Incorporated by Reference:
<bullet> For EASA material incorporated by reference in this AD,
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone
+49 221 8999 000; email <a href="/cdn-cgi/l/email-protection#9bdadfe8dbfefae8fab5feeee9f4ebfab5feee"><span class="__cf_email__" data-cfemail="da9b9ea99abfbba9bbf4bfafa8b5aabbf4bfaf">[email protected]</span></a>; website easa.europa.eu. You
may find this material on the EASA website at ad.easa.europa.eu.
<bullet> For Airbus service information identified in this final
rule, contact Airbus SAS, Airworthiness Office--EAL, Rond-Point Emile
Dewoitine No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93 36
96; fax +33 5 61 93 45 80; email <a href="/cdn-cgi/l/email-protection#74171b1a001d1a01111059151d06031b06001c1d1a1107075a15474144344815541c06111249" http: airbus.com">airbus.com</a>">continued-airworthiness.a350@<a href="http://airbus.com">airbus.com</a></a>; <a href="http://websiteairbus.com">websiteairbus.com</a>.
<bullet> You may view this service information at the FAA,
Airworthiness Products Section, Operational Safety Branch, 2200 South
216th St., Des Moines, WA. For information on the availability of this
material at the FAA, call 206-231-3195. It is also available at
<a href="http://regulations.gov">regulations.gov</a> under Docket No. FAA-2022-1576.
FOR FURTHER INFORMATION CONTACT: Dat Le, Aerospace Engineer, Large
Aircraft
[[Page 77503]]
Section, FAA, International Validation Branch, 2200 South 216th St.,
Des Moines, WA 98198; telephone 516-228-7317; email <a href="/cdn-cgi/l/email-protection#4c082d38621a6200290c2a2d2d622b233a"><span class="__cf_email__" data-cfemail="713510055f275f3d14311710105f161e07">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written data, views, or arguments
about this final rule. Send your comments to an address listed under
ADDRESSES. Include ``Docket No. FAA-2022-1576; Project Identifier MCAI-
2022-01183-T'' at the beginning of your comments. The most helpful
comments reference a specific portion of the final rule, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing date and may amend
this final rule because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
<a href="http://regulations.gov">regulations.gov</a>, including any personal information you provide. The
agency will also post a report summarizing each substantive verbal
contact received about this final rule.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this AD contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this AD, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this AD. Submissions containing CBI should be sent to Dat Le,
Aerospace Engineer, Large Aircraft Section, FAA, International
Validation Branch, 2200 South 216th St., Des Moines, WA 98198;
telephone 516-228-7317; email <a href="/cdn-cgi/l/email-protection#f1b59085dfa7dfbd94b1979090df969e87"><span class="__cf_email__" data-cfemail="c084a1b4ee96ee8ca580a6a1a1eea7afb6">[email protected]</span></a>. Any commentary that the
FAA receives which is not specifically designated as CBI will be placed
in the public docket for this rulemaking.
Background
EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2022-0183, dated August 30, 2022
(EASA AD 2022-0183) (also referred to as the MCAI), to correct an
unsafe condition for certain Airbus SAS Model A350-1041 airplanes. The
MCAI states that a loud noise and vibration in the BF area above the
wings was reported. The subsequent inspection revealed missing
fasteners on the upper fastener line at the sewing angle attachment of
the BF access panel 196ET. Further investigation determined that a
shorter fastener and inappropriate self-locking nuts may have been used
to install affected BF access panels on the final assembly line
resulting in not enough threads of the collar engaged to ensure the
locking capability. This condition, if not detected and corrected,
could lead to in-flight detachment of an affected BF access panel,
possibly resulting in damage to, and reduced control of, the airplane.
Airbus SAS has developed a new production modification (116929) to
introduce different self-locking nuts for the affected BF access
panels, increasing the design robustness. EASA AD 2022-0183 requires a
one-time detailed inspection of the affected BF access panels and,
depending on findings, accomplishment of applicable corrective actions.
The FAA is issuing this AD to address the unsafe condition on these
products. You may examine the MCAI in the AD docket at <a href="http://regulations.gov">regulations.gov</a>
under Docket No. FAA-2022-1576.
Related Service Information Under 1 CFR Part 51
EASA AD 2022-0183 requires a one-time detailed inspection of the
affected BF access panels for loose or missing fasteners, and a
detailed inspection of the bolts attached to the sewing angle of the BF
access panel to confirm that the chamfer length of the bolt is fully
extended through the nut. Depending on the inspection results, EASA AD
2022-0183 requires accomplishment of applicable corrective actions
including installing new or missing fasteners, applying torque,
replacing bolts, and repair.
The FAA reviewed Airbus Service Bulletin A350-53-P073, dated June
9, 2022, which specifies serial numbers of affected airplanes.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
FAA's Determination
This product has been approved by the aviation authority of another
country and is approved for operation in the United States. Pursuant to
the FAA's bilateral agreement with this State of Design Authority, it
has notified the FAA of the unsafe condition described in the MCAI
described above. The FAA is issuing this AD after determining that the
unsafe condition described previously is likely to exist or develop on
other products of the same type design.
Requirements of This AD
This AD requires accomplishing the actions specified in EASA AD
2022-0183 described previously, except for any differences identified
as exceptions in the regulatory text of this AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA developed a process to use some civil aviation
authority (CAA) ADs as the primary source of information for compliance
with requirements for corresponding FAA ADs. The FAA has been
coordinating this process with manufacturers and CAAs. As a result,
EASA AD 2022-0183 is incorporated by reference in this AD. This AD
requires compliance with EASA AD 2022-0183 in its entirety through that
incorporation, except for any differences identified as exceptions in
the regulatory text of this AD. Using common terms that are the same as
the heading of a particular section in EASA AD 2022-0183 does not mean
that operators need comply only with that section. For example, where
the AD requirement refers to ``all required actions and compliance
times,'' compliance with this AD requirement is not limited to the
section titled ``Required Action(s) and Compliance Time(s)'' in EASA AD
2022-0183. Service information required by EASA AD 2022-0183 for
compliance will be available at <a href="http://regulations.gov">regulations.gov</a> under Docket No. FAA-
2022-1576 after this AD is published.
FAA's Justification and Determination of the Effective Date
Section 553(b)(3)(B) of the Administrative Procedure Act (APA) (5
U.S.C. 551 et seq.) authorizes agencies to dispense with notice and
comment procedures for rules when the agency, for ``good cause,'' finds
that those procedures are ``impracticable, unnecessary, or contrary to
the public interest.'' Under this section, an agency, upon finding good
cause, may issue a final rule without providing notice and seeking
comment prior to issuance. Further, section 553(d) of the APA
authorizes agencies to make rules
[[Page 77504]]
effective in less than thirty days, upon a finding of good cause.
There are currently no domestic operators of these products.
Accordingly, notice and opportunity for prior public comment are
unnecessary, pursuant to 5 U.S.C. 553(b)(3)(B). In addition, for the
forgoing reason(s), the FAA finds that good cause exists pursuant to 5
U.S.C. 553(d) for making this amendment effective in less than 30 days.
Regulatory Flexibility Act (RFA)
The requirements of the RFA do not apply when an agency finds good
cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and
comment. Because the FAA has determined that it has good cause to adopt
this rule without notice and comment, RFA analysis is not required.
Costs of Compliance
Currently, there are no affected U.S.-registered airplanes. If an
affected airplane is imported and placed on the U.S. Register in the
future, the FAA provides the following cost estimates to comply with
this AD:
Estimated Costs for Required Actions
------------------------------------------------------------------------
Cost per
Labor cost Parts cost product
------------------------------------------------------------------------
6 work-hours x $85 per hour = $595.... $0 $595
------------------------------------------------------------------------
The FAA estimates the following costs to do any necessary on-
condition installations, replacements, or torqueing that would be
required based on the results of any required actions. The FAA has no
way of determining the number of aircraft that might need these on-
condition actions:
Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
Labor cost Parts cost Cost per product
------------------------------------------------------------------------
1 work-hour x $85 per hour = $85.. $3 $88 (per fastener or
bolt).
------------------------------------------------------------------------
The FAA has received no definitive data on which to base the cost
estimates the on-condition repairs specified in this AD.
According to the manufacturer, some or all of the costs of this AD
may be covered under warranty, thereby reducing the cost impact on
affected operators. The FAA does not control warranty coverage for
affected operators. As a result, the FAA has included all known costs
in the cost estimate.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866, and
(2) Will not affect intrastate aviation in Alaska.
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
2022-25-21 Airbus SAS: Amendment 39-22277; Docket No. FAA-2022-1576;
Project Identifier MCAI-2022-01183-T.
(a) Effective Date
This airworthiness directive (AD) is effective January 3, 2023.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Airbus SAS Model A350-1041 airplanes,
certificated in any category, having serial numbers identified in
Airbus Service Bulletin A350-53-P073, dated June 9, 2022.
(d) Subject
Air Transport Association (ATA) of America Code: 53, Fuselage.
(e) Unsafe Condition
This AD was prompted by a report of a loud noise and vibration
in the belly fairing (BF) access panel above the wings. The FAA is
issuing this AD to address missing fasteners on the BF access panels
due to the use of shorter fasteners and inappropriate self-locking
nuts resulting in not enough threads of the collar engaged to ensure
the locking capability. The unsafe condition, if not addressed,
could result in an in-flight detachment of an affected BF access
panel, possibly resulting in damage to, and reduced control of, the
airplane.
[[Page 77505]]
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, European Union Aviation Safety Agency (EASA) AD
2022-0183, dated August 30, 2022 (EASA AD 2022-0183).
(h) Exceptions to EASA AD 2022-0183
(1) Where EASA AD 2022-0183 refers to its effective date, this
AD requires using the effective date of this AD.
(2) Where the service information referenced in EASA AD 2022-
0183 specifies to do certain actions ``in accordance with the IPD,''
for this AD replace the text ``in accordance with'' with ``refer
to.''
(3) Where paragraph (2) of EASA AD 2022-0183 refers to a
``defect,'' for purposes of this AD, a defect includes a loose or
missing fastener, and a bolt whose length does not fully extend
through the nut.
(4) The ``Remarks'' section of EASA AD 2022-0183 does not apply
to this AD.
(i) No Reporting Requirement
Although the service information referenced in EASA AD 2022-0183
specifies to submit certain information to the manufacturer, this AD
does not include that requirement.
(j) Additional AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Validation Branch, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. In accordance with 14 CFR 39.19, send your request to your
principal inspector or responsible Flight Standards Office, as
appropriate. If sending information directly to the manager of the
certification office, send it to the attention of the person
identified in paragraph (k) of this AD. Information may be emailed
to: <a href="/cdn-cgi/l/email-protection#c4fde9859297e9858d96e9f3f7f4e985898b8784a2a5a5eaa3abb2"><span class="__cf_email__" data-cfemail="526b7f1304017f131b007f6561627f131f1d11123433337c353d24">[email protected]</span></a>. Before using any approved AMOC,
notify your appropriate principal inspector, or lacking a principal
inspector, the manager of the responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, International
Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design
Organization Approval (DOA). If approved by the DOA, the approval
must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by
paragraph (j)(2) of this AD, if any service information contains
procedures or tests that are identified as RC, those procedures and
tests must be done to comply with this AD; any procedures or tests
that are not identified as RC are recommended. Those procedures and
tests that are not identified as RC may be deviated from using
accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC, provided
the procedures and tests identified as RC can be done and the
airplane can be put back in an airworthy condition. Any
substitutions or changes to procedures or tests identified as RC
require approval of an AMOC.
(k) Additional Information
For more information about this AD, contact Dat Le, Aerospace
Engineer, Large Aircraft Section, FAA, International Validation
Branch, 2200 South 216th St., Des Moines, WA 98198; telephone 516-
228-7317; email <a href="/cdn-cgi/l/email-protection#024663762c542c4e67426463632c656d74"><span class="__cf_email__" data-cfemail="a7e3c6d389f189ebc2e7c1c6c689c0c8d1">[email protected]</span></a>.
(l) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless this AD specifies otherwise.
(i) Airbus Service Bulletin A350-53-P073, dated June 9, 2022.
(ii) European Union Aviation Safety Agency (EASA) AD 2022-0183,
dated August 30, 2022.
(3) For EASA AD 2022-0183, contact EASA, Konrad-Adenauer-Ufer 3,
50668 Cologne, Germany; telephone +49 221 8999 000; email
<a href="/cdn-cgi/l/email-protection#febfba8dbe9b9f8d9fd09b8b8c918e9fd09b8b"><span class="__cf_email__" data-cfemail="7435300734111507155a1101061b04155a1101">[email protected]</span></a>; website easa.europa.eu. You may find this EASA
AD on the EASA website at ad.easa.europa.eu.
(4) For Airbus service information identified in this AD,
contact Airbus SAS, Airworthiness Office--EAL, Rond-Point Emile
Dewoitine No: 2, 31700 Blagnac Cedex, France; telephone +33 5 61 93
36 96; fax +33 5 61 93 45 80; email <a href="/cdn-cgi/l/email-protection#0d6e6263796463786869206c647f7a627f79656463687e7e236c3e383d4d316c2d657f686b30" http: airbus.com">airbus.com</a>">continued-airworthiness.a350@<a href="http://airbus.com">airbus.com</a></a>; website <a href="http://airbus.com">airbus.com</a>.
(5) You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St.,
Des Moines, WA. For information on the availability of this material
at the FAA, call 206-231-3195.
(6) You may view this material that is incorporated by reference
at the National Archives and Records Administration (NARA). For
information on the availability of this material at NARA, email
<a href="/cdn-cgi/l/email-protection#7c1a0e5215120f0c191f081513123c121d0e1d521b130a"><span class="__cf_email__" data-cfemail="660014480f0815160305120f0908260807140748010910">[email protected]</span></a>, or go to: <a href="http://www.archives.gov/federal-register/cfr/ibr-locations.html">www.archives.gov/federal-register/cfr/ibr-locations.html</a>.
Issued on December 5, 2022.
Christina Underwood,
Acting Director, Compliance & Airworthiness Division, Aircraft
Certification Service.
[FR Doc. 2022-27403 Filed 12-16-22; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on December 19, 2022.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.