Rule2021-25534
Airworthiness Directives; Airbus SAS Airplanes
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
November 24, 2021
Effective
December 29, 2021
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by a report of a broken forward guide arm found during a passenger door emergency opening test. Investigation results indicated that the opening speed of the door was higher than expected, likely caused by a reduced damping due to oil leakage of the passenger door damper emergency opening actuator (DEOA). This AD requires repetitively replacing certain forward and aft guide arms on the passenger door, inspecting the forward and aft guide arm support brackets for damage, modifying certain DEOAs, and repairing damage if necessary, and also provides an optional terminating action for the repetitive replacements, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 86 Issue 224 (Wednesday, November 24, 2021)</title>
</head>
<body><pre>
[Federal Register Volume 86, Number 224 (Wednesday, November 24, 2021)]
[Rules and Regulations]
[Pages 66945-66948]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2021-25534]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2021-0545; Project Identifier MCAI-2021-00071-T;
Amendment 39-21791; AD 2021-22-18]
RIN 2120-AA64
Airworthiness Directives; Airbus SAS Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all
Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by
a report of a broken forward guide arm found during a passenger door
emergency opening test. Investigation results indicated that the
opening speed of the door was higher than expected, likely caused by a
reduced damping due to oil leakage of the passenger door damper
emergency opening actuator (DEOA). This AD requires repetitively
replacing certain forward and aft guide arms on the passenger door,
inspecting the forward and aft guide arm support brackets for damage,
modifying certain DEOAs, and repairing damage if necessary, and also
provides an optional terminating action for the repetitive
replacements, as specified in a European Union Aviation Safety Agency
(EASA) AD, which is incorporated by reference. The FAA is issuing this
AD to address the unsafe condition on these products.
DATES: This AD is effective December 29, 2021.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of December 29,
2021.
ADDRESSES: For material incorporated by reference (IBR) in this AD,
contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone
+49 221 8999 000; email <a href="/cdn-cgi/l/email-protection#befffacdfedbdfcddf90dbcbccd1cedf90dbcb"><span class="__cf_email__" data-cfemail="b9f8fdcaf9dcd8cad897dccccbd6c9d897dccc">[email protected]</span></a>; internet
www.easa.europa.eu. You may find this IBR material on the EASA website
at <a href="https://ad.easa.europa.eu">https://ad.easa.europa.eu</a>. You may view this IBR material at the
FAA, Airworthiness Products Section, Operational Safety Branch, 2200
South 216th St., Des Moines, WA. For information on the availability of
this material at the FAA, call 206-231-3195. It is also available in
the AD docket on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by
searching for and locating Docket No. FAA-2021-0545.
Examining the AD Docket
You may examine the AD docket at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by
searching for and locating Docket No. FAA-2021-0545; or in person at
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The AD docket contains this final rule, the
mandatory continuing airworthiness information (MCAI), any comments
received, and other information. The address for Docket Operations is
U.S. Department of Transportation, Docket Operations, M-30, West
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer, Large
Aircraft Section, FAA, International Validation Branch, 2200 South
216th St., Des Moines, WA 98198; telephone and fax 206-231-3225; email
<a href="/cdn-cgi/l/email-protection#d3b7b2bdfda1bcb7babdb293b5b2b2fdb4bca5"><span class="__cf_email__" data-cfemail="3e5a5f50104c515a57505f7e585f5f10595148">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Background
EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2021-0085, dated March 19, 2021
(EASA AD 2021-0085) (also referred to as the Mandatory Continuing
Airworthiness Information, or the MCAI), to correct an unsafe condition
for all Airbus SAS Model A350-941 and -1041 airplanes. EASA AD 2021-
0085 superseded EASA AD 2021-0018, dated January 15, 2021.
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 by adding an AD that would apply to all Airbus SAS Model
A350-941 and -1041 airplanes. The NPRM published in the Federal
Register on July 6, 2021 (86 FR 35413). The NPRM was prompted by a
report of a broken forward guide arm found during a passenger door
emergency opening test. Investigation results indicated that the
opening speed of the door was higher than expected, likely caused by a
reduced damping due to oil leakage of the passenger door DEOA. The NPRM
proposed to require repetitively replacing certain forward and aft
guide arms on the passenger door, inspecting the forward and aft guide
arm support brackets for damage, modifying certain DEOAs, and repairing
damage if necessary, and also proposed to provide an optional
terminating action for the repetitive replacements, as specified in
EASA AD 2021-0085.
The FAA is issuing this AD to address failure of a passenger door
to perform its intended function during an emergency opening, which
could result in reduced evacuation capacity from the airplane and
injury to occupants. See the MCAI for additional background
information.
Discussion of Final Airworthiness Directive
Comments
The FAA received comments from one commenter. The following
presents the comments received on the NPRM and the FAA's response to
each comment.
Request To Add Exceptions to MCAI Specifications
Delta Air Lines Inc. (DAL) asked that the FAA add a new exception
paragraph to the proposed AD to allow the replacement of DEOA part
number (P/N) FE396001001 with DEOA P/N FE396001004, FE396001005, or
FE396001006 (or later model), in addition to DEOA P/N FE396001003
currently included in the instructions. DAL stated that the RC
(required for compliance) instructions appear to limit operators to
install only P/N FE396001003. DAL sent in a request for clarification
from Airbus in which Airbus clarified that DEOA P/N FE396001001 can be
replaced with DEOA P/N FE396001003, FE396001004, FE396001005, or
FE396001006, since P/Ns FE396001003, FE396001004, FE396001005, and
FE396001006 are interchangeable.
The FAA agrees with the commenter's request, for the reasons
provided. The FAA has added the exception in paragraph (h)(6) of this
AD.
DAL also asked that the FAA add another new exception paragraph to
the proposed AD, as follows: ``For this AD,
[[Page 66946]]
DEOAs which are not `new' may be used when completing the instructions
in Airbus Service Bulletin A350-52-P049, Rev 00, Option 2, as long as
they fit the definition of a `serviceable part' per EASA AD 2021-0085,
and do not have part number [P/N] FE396001001 (i.e., P/N FE396001003,
FE396001004, FE396001005, FE396001006 or later).'' DAL stated that, the
DEOA replacement in Option 2 of Airbus Service Bulletin A350-52-P049,
dated January 15, 2021, provides instructions to install a ``new''
DEOA. However, DAL believes that the word ``serviceable'' should be
used rather than ``new'' in the instructions. DAL noted that Airbus may
have inadvertently limited operators to only ``new'' actuators when
otherwise ``used'' serviceable DEOAs would be acceptable per the
definitions of ``serviceable part'' in the referenced service
information. DAL added that it understands that the supply of these
DEOAs is low worldwide, and serviceable parts, as defined by EASA AD
2021-0085, may not necessarily be ``new.'' They may be overhauled,
repaired, upgraded, modified, etc. DAL stated that such a DEOA will
still be compliant with EASA AD 2021-0085, as long as the DEOA is in
the ``serviceable'' configuration and does not have P/N FE396001001
(i.e., has P/N FE396001003, FE396001004, FE396001005, FE396001006, or
later). Because DAL is planning to ship affected (discrepant) P/N
FE396001001 DEOAs back to the original equipment manufacturer (OEM) for
modification, and P/N FE396001001 may be modified to become a
``serviceable part,'' the possibility exists that DAL could receive
serviceable parts (DEOAs other than P/N FE396001001) that may not
necessarily be ``new'' according to the associated delivery documents.
The FAA agrees with the commenter's request, for the reasons
provided. DEOAs that are ``serviceable'' may be used during
accomplishment of the instructions in Airbus Service Bulletin A350-52-
P049, Option 2, provided the part fits the definition of a
``serviceable part'' per EASA AD 2021-0085. The FAA has added the
exception in paragraph (h)(7) of this AD.
DAL asked that paragraph (h) be revised to add an exception to
Airbus Service Bulletin A350-52-P049, which states to use CML 04SBA3
varnish polyurethane to protect the identification plate during
modification or replacement of the door actuator. DAL stated that the
proposed AD should allow the use of CA8800/B900 in lieu of CML 04SBA3.
The FAA agrees with the commenter's request. Airbus has granted DAL
permission to use the material CA8800/B900 in lieu of the CML 04SBA3
materials. The FAA has added this exception in paragraph (h)(10) of
this AD.
Request To Clarify Compliance Time for Replacement
DAL asked that the compliance time in paragraph (2) of EASA AD
2021-0085 be clarified in the proposed AD as an exception. DAL stated
that 15 days means 15 days ``in-service'' on an airplane. DAL stated
that EASA AD 2021-0085 contains no provisions for used spare doors on
which the 15-day guide arm replacement required by that paragraph may
have already been exceeded. DAL noted that an operator could have a
spare door (or acquire a spare door) that may have previously had an
emergency opening with an affected DEOA, and may not have had the guide
arms replaced within 15 days, and if the operator wishes to install the
spare door, the replacement requirement cannot be complied with in 15
days, since 15 days may have already elapsed. DAL concluded that any
installation of a spare door that has had an emergency opening with the
affected actuator would require requesting an alternative method of
compliance (AMOC) for the guide arm replacement time.
The FAA disagrees with the request. The grace period of 15 days is
sufficient to accomplish the task and is unrelated to on-aircraft
usage. For spare parts subject to this AD for which the grace period
has elapsed, the AD actions would be required prior to reinstallation
on an airplane. No change to the AD is made in this regard.
Request To Correct Cotter Pin Part Number
DAL asked that the proposed AD be revised to add an exception to
correct the cotter pin part number identified as P/N MS24665-155 in
Airbus Service Bulletin A350-52-P050, dated December 15, 2020, which is
referenced in the EASA AD. DAL stated that the proposed AD should allow
the use of cotter pins having the correct P/N MS24665-300.
The FAA agrees with the commenter's request. Airbus issued
Operators Information Transmission (OIT)--SBIT 21-0014, dated July 8,
2021, to inform operators that P/N MS24665-155 is an incorrect part
number for a cotter pin. Therefore, the FAA has added an exception in
paragraph (h)(8) of this AD, which requires the use of cotter pins
having P/N MS24665-300 instead of cotter pin P/N MS24665-155.
Request To Relocate Configured Spare Component (CSC) Number Marking
DAL asked that the proposed AD include an exception to correct the
location to mark the CSC number. DAL stated that Airbus Service
Bulletin A350-52-P049, dated January 15, 2021, specifies instructions
to mark the new CSC number on the door label. DAL noted that an
exception should require the new CSC number to be marked on the
identification plate instead. DAL stated that the terms ``door label''
and ``identification plate'' appear to be used interchangeably in the
referenced service information. DAL noted that as written, the
instructions specified in Airbus Service Bulletin A350-52-P049 are
confusing because there is both an identification plate and a door
label on the door in the referenced figures; therefore, the
instructions incorrectly state to mark the new CSC number on the door
label instead of the identification plate. DAL requested confirmation
from Airbus that the instructions were incorrect and was informed that
the intent of the referenced service information is to mark the new CSC
number on the identification plate and not the door label. Airbus
issued Repair Design Approval Form (RDAF) 80876584/008/2021#A, dated
February 8, 2021, to provide DOA confirmation of the incorrect
instructions. The RDAF confirmed that the door label is not to be
altered, and the re-identification is to be done to the identification
plate only.
The FAA agrees with the commenter's request, for the reasons
provided. The instructions specified in Airbus Service Bulletin A350-
52-P049 incorrectly specify marking the new CSC number on the door
label. Therefore, the FAA has added an exception in paragraph (h)(8) of
this AD, which requires the new CSC number to be marked on the
identification plate.
Request for Clarification of Terminology
DAL asked for clarification of the terminology used since the terms
``rod'' and ``guide arms'' are used interchangeably in Airbus Service
Bulletin A350-52-P050, dated December 15, 2020, but not in the proposed
AD. DAL stated that in order to reduce potential confusion as to which
part is to be replaced, the proposed AD should include a statement that
clearly defines that the terms ``rod'' and ``guide arms'' are used
interchangeably.
The FAA agrees that ``guide arms'' and ``rods'' mean the same
thing. The term ``guide arms'' is used in the
[[Page 66947]]
preamble of this AD; however, those terms are not specifically cited in
the regulatory text. Therefore, the FAA has not changed this AD in this
regard.
Request To Allow Parts Return
DAL asked that the proposed AD include an exception to allow the
return of affected actuators to the OEM after accomplishing the
instructions in Airbus Service Bulletin A350-52-P049, dated January 15,
2021. DAL stated that Option 2 of Airbus Service Bulletin A350-52-P049
provides instructions to replace the affected part (DEOA P/N
FE396001001) and discard the DEOA with P/N FE396001001 upon
replacement. However, DAL stated it intends to ship the removed DEOA
back to the OEM for upgrade per its retrofit agreement instructions,
rather than discarding the DEOA. DAL requested that the final rule
state that return of affected actuators to the OEM is acceptable when
accomplishing the instructions in Airbus Service Bulletin A350-52-P049.
The FAA acknowledges the commenter's request; however, this AD does
not include a requirement that affected parts must be returned to the
OEM. Returning affected parts is at the operator's discretion. However,
the FAA has added an exception in paragraph (h)(11) of this AD to
provide clarification that returning affected parts is not required by
this AD.
Conclusion
The FAA reviewed the relevant data, considered the comments
received, and determined that air safety requires adopting this AD as
proposed. Except for minor editorial changes, and any other changes
described previously, this AD is adopted as proposed in the NPRM. None
of the changes will increase the economic burden on any operator.
Accordingly, the FAA is issuing this AD to address the unsafe condition
on these products.
Related Service Information Under 1 CFR Part 51
EASA AD 2021-0085 describes procedures for repetitively replacing
the forward and aft guide arms following any passenger door emergency
opening, modifying the airplane so that there is a maximum of one
affected DEOA per door pair (left- and right-hand sides), inspecting
the forward and aft guide arm support brackets for damage, and repair.
EASA AD 2021-0085 also describes procedures for the optional
replacement of each affected DEOA having P/N FE396001001, which is
terminating action for the repetitive replacements. This material is
reasonably available because the interested parties have access to it
through their normal course of business or by the means identified in
the ADDRESSES section.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
2021-22-18 Airbus SAS: Amendment 39-21791; Docket No. FAA-2021-0545;
Project Identifier MCAI-2021-00071-T.
(a) Effective Date
This airworthiness directive (AD) is effective December 29,
2021.
(b) Affected ADs
None.
(c) Applicability
This AD applies to all Airbus SAS Model A350-941 and -1041
airplanes, certificated in any category.
(d) Subject
Air Transport Association (ATA) of America Code 52, Doors.
(e) Reason
This AD was prompted by a report of a broken forward guide arm
found during a passenger door emergency opening test. Investigation
results indicated that the opening speed of the door was higher than
expected, likely caused by a reduced damping due to oil leakage of
the passenger door damper emergency opening actuator (DEOA). The FAA
is issuing this AD to address failure of a passenger door to perform
its intended function during an emergency opening, which could
result in reduced evacuation capacity from the airplane and injury
to occupants.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, European Union Aviation Safety Agency (EASA) EASA
AD 2021-0085, dated March 19, 2021 (EASA AD 2021-0085).
(h) Exceptions and Clarifications to EASA AD 2021-0085
(1) Where EASA AD 2021-0085 refers to January 29, 2021 (the
effective date of EASA AD 2021-0018), this AD requires using the
effective date of this AD.
(2) Where EASA AD 2021-0085 refers to its effective date, this
AD requires using the effective date of this AD.
(3) This AD does not mandate compliance with the ``Remarks''
section of EASA AD 2021-0085.
(4) Where paragraphs (4) and (5) of EASA AD 2021-0085 refer to
``the limits as defined in the inspection SB [service bulletin],''
for this AD use ``the limits as defined in ASR [aircraft structural
repair] A350-A-51-73-11-01ZZZ-667Z-A.''
(5) Where paragraphs (1) and (2) of EASA AD 2021-0085 specify to
``replace the forward and aft guide arms on that door in
[[Page 66948]]
accordance with the instructions of the inspection SB,'' this AD
requires ``removing the forward and aft guide arms on that door, in
accordance with the instructions of the inspection SB; doing a
detailed inspection of the forward and aft guide arm support bracket
on that door and all applicable corrective actions as specified in
paragraphs (3) through (5) of EASA AD 2021-0085; and installing new
forward and aft guide arms on that door, in accordance with the
instructions of the inspection SB.''
(6) Where paragraph (6) of EASA AD 2021-0085 specifies to modify
the airplane ``in accordance with the instructions of the
modification SB,'' this AD allows the replacement of DEOA P/N
FE396001001with DEOA P/N FE396001004, FE396001005, or FE396001006,
in addition to DEOA P/N FE396001003.
(7) Where paragraph (6) of EASA AD 2021-0085 specifies to modify
the airplane ``in accordance with the instructions of the
modification SB'', this AD allows DEOAs that are ``serviceable'' to
be used as replacement parts, provided the part fits the definition
of a ``serviceable part'' as identified in EASA AD 2021-0085.
(8) Where paragraph (4) of EASA AD 2021-0085 specifies to
accomplish the applicable corrective actions ``in accordance with
the instructions of the inspection SB,'' this AD requires the use of
cotter pins having P/N MS24665-300 instead of cotter pins having P/N
MS24665-155.
(9) Where paragraphs (6) and (7) of EASA AD 2021-0085 specify to
modify the airplane to ensure that there is a maximum of one
affected part per door pair and that replacement of each affected
part is terminating action, which involves the use of CML 04SBA3
varnish polyurethane to protect the identification plate, this AD
also allows the use of CA8800/B900 varnish polyurethane in lieu of
the CML 04SBA3 varnish polyurethane.
(11) Where the service information referenced in EASA AD 2021-
0085 specifies discarding discrepant parts, this AD does not require
that action.
(i) No Reporting Requirement
Although the service information referenced in EASA AD 2021-0085
specifies to submit certain information to the manufacturer, this AD
does not include that requirement.
(j) Additional AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
Large Aircraft Section, International Validation Branch, FAA, has
the authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or responsible Flight
Standards Office, as appropriate. If sending information directly to
the Large Aircraft Section, International Validation Branch, send it
to the attention of the person identified in paragraph (k)(2) of
this AD. Information may be emailed to: <a href="/cdn-cgi/l/email-protection#586175190e0b7519110a756f6b68751915171b183e3939763f372e"><span class="__cf_email__" data-cfemail="1e27335f484d335f574c33292d2e335f53515d5e787f7f30797168">[email protected]</span></a>.
Before using any approved AMOC, notify your appropriate principal
inspector, or lacking a principal inspector, the manager of the
responsible Flight Standards Office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, Large Aircraft
Section, International Validation Branch, FAA; or EASA; or Airbus
SAS's EASA Design Organization Approval (DOA). If approved by the
DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by
paragraph (j)(2) of this AD, if any service information contains
procedures or tests that are identified as RC, those procedures and
tests must be done to comply with this AD; any procedures or tests
that are not identified as RC are recommended. Those procedures and
tests that are not identified as RC may be deviated from using
accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC, provided
the procedures and tests identified as RC can be done and the
airplane can be put back in an airworthy condition. Any
substitutions or changes to procedures or tests identified as RC
require approval of an AMOC.
(k) Related Information
For more information about this AD, contact Dan Rodina,
Aerospace Engineer, Large Aircraft Section, FAA, International
Validation Branch, 2200 South 216th St., Des Moines, WA 98198;
telephone and fax 206-231-3225; email <a href="/cdn-cgi/l/email-protection#37535659194558535e59567751565619505841"><span class="__cf_email__" data-cfemail="690d0807471b060d000708290f0808470e061f">[email protected]</span></a>.
(l) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference of the service information listed in this
paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless this AD specifies otherwise.
(i) European Union Aviation Safety Agency (EASA) AD 2021-0085,
dated March 19, 2021.
(ii) [Reserved]
(3) For EASA AD 2021-0085, contact EASA, Konrad-Adenauer-Ufer 3,
50668 Cologne, Germany; telephone +49 221 8999 000; email
<a href="/cdn-cgi/l/email-protection#09484d7a496c687a68276c7c7b667968276c7c"><span class="__cf_email__" data-cfemail="db9a9fa89bbebaa8baf5beaea9b4abbaf5beae">[email protected]</span></a>; internet www.easa.europa.eu. You may find this
EASA AD on the EASA website at <a href="https://ad.easa.europa.eu">https://ad.easa.europa.eu</a>.
(4) You may view this material at the FAA, Airworthiness
Products Section, Operational Safety Branch, 2200 South 216th St.,
Des Moines, WA. For information on the availability of this material
at the FAA, call 206-231-3195.
(5) You may view this material that is incorporated by reference
at the National Archives and Records Administration (NARA). For
information on the availability of this material at NARA, email
<a href="/cdn-cgi/l/email-protection#395f4b1750574a495c5a4d5056577957584b58175e564f"><span class="__cf_email__" data-cfemail="583e2a7631362b283d3b2c3137361836392a39763f372e">[email protected]</span></a>, or go to: <a href="https://www.archives.gov/federal-register/cfr/ibr-locations.html">https://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.
Issued on October 21, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification
Service.
[FR Doc. 2021-25534 Filed 11-23-21; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on November 24, 2021.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.