Airworthiness Directives; Leonardo S.p.a. Helicopters
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Issuing agencies
Abstract
The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.a. Model AB139, AW139, AB412, and AB412 EP helicopters. This AD was prompted by failure of an Emergency Flotation System (EFS) float compartment to inflate during maintenance of the EFS. This AD requires inspecting certain EFSs and depending on the results, marking certain parts or removing certain parts from service, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 86 Issue 198 (Monday, October 18, 2021)</title>
</head>
<body><pre>
[Federal Register Volume 86, Number 198 (Monday, October 18, 2021)]
[Rules and Regulations]
[Pages 57567-57569]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2021-22470]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2021-0608; Project Identifier 2019-SW-119-AD; Amendment
39-21750; AD 2021-20-12]
RIN 2120-AA64
Airworthiness Directives; Leonardo S.p.a. Helicopters
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for
certain Leonardo S.p.a. Model AB139, AW139, AB412, and AB412 EP
helicopters. This AD was prompted by failure of an Emergency Flotation
System (EFS) float compartment to inflate during maintenance of the
EFS. This AD requires inspecting certain EFSs and depending on the
results, marking certain parts or removing certain parts from service,
as specified in a European Union Aviation Safety Agency (EASA) AD,
which is incorporated by reference. The FAA is issuing this AD to
address the unsafe condition on these products.
DATES: This AD is effective November 22, 2021.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of November 22,
2021.
ADDRESSES: For EASA material incorporated by reference (IBR) in this
AD, contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany;
telephone +49 221 8999 000; email <a href="/cdn-cgi/l/email-protection#8ccdc8ffcce9edffeda2e9f9fee3fceda2e9f9"><span class="__cf_email__" data-cfemail="aeefeaddeecbcfddcf80cbdbdcc1decf80cbdb">[email protected]</span></a>; internet
www.easa.europa.eu. You may find this material on the EASA website at
<a href="https://ad.easa.europa.eu">https://ad.easa.europa.eu</a>. For Leonardo Helicopters and Safran material
identified in this final rule, contact Leonardo S.p.A. Helicopters,
Emanuele Bufano, Head of Airworthiness, Viale G.Agusta 520, 21017
C.Costa di Samarate (Va) Italy; telephone +39-0331-225074; fax +39-
0331-229046; or at <a href="https://customerportal.leonardocompany.com/en-US/">https://customerportal.leonardocompany.com/en-US/</a>.
You may view this material at the FAA, Office of the Regional Counsel,
Southwest Region, 10101 Hillwood Pkwy., Room 6N-321, Fort Worth, TX
76177. For information on the availability of this material at the FAA,
call 817-222-5110. The EASA material is also available in the AD docket
at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No.
FAA-2021-0608.
Examining the AD Docket
You may examine the AD docket at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by
searching for and locating Docket No. FAA-2021-0608; or in person at
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The AD docket contains this final rule, any
comments received, and other information. The address for Docket
Operations is U.S. Department of Transportation, Docket Operations, M-
30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue
SE, Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Andrea Jimenez, Aerospace Engineer,
COS Program Management Section, Operational Safety Branch, Compliance &
Airworthiness Division, FAA, 1600 Stewart Ave., Suite 410, Westbury, NY
11590; telephone (516) 228-7330; email <a href="/cdn-cgi/l/email-protection#aacbc4ced8cfcb84c0c3c7cfc4cfd0eacccbcb84cdc5dc"><span class="__cf_email__" data-cfemail="46272822342327682c2f2b2328233c0620272768212930">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Background
The EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2019-0311, dated December 19, 2019
(EASA AD 2019-0311), to correct an unsafe condition for Leonardo
S.p.A., formerly Finmeccanica Helicopter Division, AgustaWestland,
Agusta S.p.A., Model AB139, AW139, AB412, and AB412EP helicopters.
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 by adding an AD that would apply to certain Leonardo S.p.a.
Model AB139, AW139, AB412, and AB412EP helicopters. The NPRM published
in the Federal Register on July 30, 2021 (86 FR 40962). The NPRM was
prompted by failure of an EFS float compartment to inflate during
maintenance of the EFS. The NPRM proposed to require inspecting each
EFS supply hose and depending on the results, re-identifying or
removing the EFS supply hose from service, as specified in an EASA AD.
The FAA is issuing this AD to address a blocked float supply hose.
See EASA AD 2019-0311 for additional background information.
[[Page 57568]]
Discussion of Final Airworthiness Directive
Comments
The FAA gave the public the opportunity to participate in
developing this final rule. The FAA received no comments on the NPRM or
on the determination of the cost to the public.
Conclusion
The FAA reviewed the relevant data and determined that air safety
and the public interest require adopting this final rule as proposed.
Related Service Information Under 1 CFR Part 51
EASA AD 2019-0311 specifies inspecting certain EFSs and depending
on the results, re-identifying the float supply hose with a green heat
shrinkable sleeve if the float supply hose passes an inspection, or
replacing the float supply hose with a serviceable float supply hose.
EASA AD 2019-0311 also prohibits installing a float supply hose unless
it passes the inspection and is re-identified.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
Other Related Service Information
The FAA reviewed Safran Service Bulletin 025-69-19, Revision 00,
dated November 22, 2019 (SB 025-69-19), which is attached as Annex A to
Leonardo Helicopters Alert Service Bulletin (ASB) No. 139-610 and
Emergency ASB No. 412-157, each dated December 17, 2019. SB 025-69-19
specifies procedures for inspecting for blockage through the float
supply hoses of the EFS inflation system.
Differences Between This AD and the EASA AD
EASA AD 2019-0311 requires inspecting each affected part in Group A
within 400 flight hours (FH) or 12 months, whichever occurs first,
whereas this AD requires inspecting each affected part in that group
within 100 hours time-in-service instead. EASA AD 2019-0311 requires
inspecting each affected part in Group C within 300 FH or during the
next scheduled ``18 months'' inspection, whichever occurs first,
whereas this AD requires inspecting each affected part in that group
within 15 hours time-in-service instead to address the unsafe condition
as soon as practical as there are no Group C aircraft registered in the
U.S.; the proposed compliance time matches those same model aircraft
found in Group D. Where the service information referenced in EASA AD
2019-0311 specifies ``operator able to perform the EFS maintenance in
accordance with Aircraft Maintenance Manual (AMM) or Aircraft
Maintenance Publication (AMP) can perform the procedure defined in this
Service Bulletin,'' this AD requires that the work be accomplished by a
mechanic that meets the requirements of 14 CFR part 65 subpart D. Where
EASA AD 2019-0311 specifies replacing an affected float supply hose
that fails the inspection, this AD requires removing the float supply
hose from service instead.
Costs of Compliance
The FAA estimates that this AD affects 129 helicopters of U.S.
Registry. Labor rates are estimated at $85 per work-hour. Based on
these numbers, the FAA estimates that operators may incur the following
costs in order to comply with this AD.
Inspecting each EFS supply hose takes about 0.25 work-hour for an
estimated cost of $21 per hose. Re-identifying each EFS supply hose
would take a minimal amount of time at a nominal cost.
Replacing an EFS supply hose takes up to 8 work-hours and parts
cost between $2,500 and $9,500 for a set of float supply hoses, for an
estimated cost of up to $10,180 per helicopter.
According to Safran's service information, some of the costs of
this AD may be covered under warranty, thereby reducing the cost impact
on affected individuals. The FAA does not control warranty coverage by
Safran; accordingly, all costs are included in this cost estimate.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order
13132. This AD will not have a substantial direct effect on the States,
on the relationship between the national government and the States, or
on the distribution of power and responsibilities among the various
levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
2021-20-12 Leonardo S.p.a: Amendment 39-21750; Docket No. FAA-2021-
0608; Project Identifier 2019-SW-119-AD.
(a) Effective Date
This airworthiness directive (AD) is effective November 22,
2021.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Leonardo S.p.a. Model AB139, AW139, AB412,
and AB412 EP helicopters, certificated in any category, with an
affected part as identified in European Union Aviation Safety Agency
(EASA) AD 2019-0311, dated December 19, 2019 (EASA AD 2019-0311),
installed.
(d) Subject
Joint Aircraft System Component (JASC) Code: 3212, Emergency
Flotation Section.
[[Page 57569]]
(e) Unsafe Condition
This AD was prompted by failure of an Emergency Flotation System
(EFS) float compartment to inflate during maintenance of the EFS.
The FAA is issuing this AD to address a blocked float supply hose.
The unsafe condition, if not addressed, could result in partial
inflation of an EFS float during an emergency landing on water and
subsequently preventing a timely egress from the helicopter, which
could result in injury to helicopter occupants.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, EASA AD 2019-0311.
(h) Exceptions to EASA AD 2019-0311
(1) Where EASA AD 2019-0311 refers to its effective date, this
AD requires using the effective date of this AD.
(2) Where EASA AD 2019-0311 requires compliance in terms of
flight hours, this AD requires using hours time-in-service (TIS).
(3) Where paragraph (1) of EASA AD 2019-0311 requires inspecting
each affected part within the compliance time specified in Table 2
of its AD, this AD requires:
(i) Inspecting each affected part in Group A within 100 hours
TIS after the effective date of this AD.
(ii) Inspecting each affected part in Group C within 15 hours
TIS after the effective date of this AD.
(4) Where the service information referenced in paragraph (1) of
EASA AD 2019-0311 specifies ``operator able to perform the EFS
maintenance in accordance with Aircraft Maintenance Manual (AMM) or
Aircraft Maintenance Publication (AMP) can perform the procedure
defined in this Service Bulletin,'' this AD requires that the work
be accomplished by a mechanic that meets the requirements of 14 CFR
part 65 subpart D.
(5) Where paragraph (2) of EASA AD 2019-0311 specifies replacing
an EFS supply hose that fails the inspection, this AD requires
removing the hose from service.
(6) This AD does not require the ``Remarks'' section of EASA AD
2019-0311.
(i) No Reporting Requirement
Although the service information referenced in EASA AD 2019-0311
specifies to submit certain information to the manufacturer, this AD
does not include that requirement.
(j) Alternative Methods of Compliance (AMOCs)
(1) The Manager, International Validation Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the International Validation Branch, send
it to the attention of the person identified in paragraph (k) of
this AD. Information may be emailed to: <a href="/cdn-cgi/l/email-protection#6d54402c3b3e402c243f405a5e5d402c20222e2d0b0c0c430a021b"><span class="__cf_email__" data-cfemail="21180c6077720c6068730c1612110c606c6e62614740400f464e57">[email protected]</span></a>.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(k) Related Information
For more information about this AD, contact Andrea Jimenez,
Aerospace Engineer, COS Program Management Section, Operational
Safety Branch, Compliance & Airworthiness Division, FAA, 1600
Stewart Ave., Suite 410, Westbury, NY 11590; telephone (516) 228-
7330; email <a href="/cdn-cgi/l/email-protection#a7c6c9c3d5c2c689cdcecac2c9c2dde7c1c6c689c0c8d1"><span class="__cf_email__" data-cfemail="ef8e818b9d8a8ec18586828a818a95af898e8ec1888099">[email protected]</span></a>.
(l) Material Incorporated by Reference
(1) The Director of the Federal Register approved the
incorporation by reference (IBR) of the service information listed
in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do
the actions required by this AD, unless this AD specifies otherwise.
(i) European Union Aviation Safety Agency (EASA) AD 2019-0311,
dated December 19, 2019.
(ii) [Reserved]
(3) For EASA AD 2019-0311, contact the EASA, Konrad-Adenauer-
Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email
<a href="/cdn-cgi/l/email-protection#ca8b8eb98aafabb9abe4afbfb8a5baabe4afbf"><span class="__cf_email__" data-cfemail="7332370033161200125d1606011c03125d1606">[email protected]</span></a>; internet www.easa.europa.eu. You may find this
EASA AD on the EASA website at <a href="https://ad.easa.europa.eu">https://ad.easa.europa.eu</a>.
(4) You may view this service information at the FAA, Office of
the Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room
6N-321, Fort Worth, TX 76177. For information on the availability of
this material at the FAA, call 817-222-5110. This material may be
found in the AD docket at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching
for and locating Docket No. FAA-2021-0608.
(5) You may view this material that is incorporated by reference
at the National Archives and Records Administration (NARA). For
information on the availability of this material at NARA, email
<a href="/cdn-cgi/l/email-protection#8fe9fda1e6e1fcffeaecfbe6e0e1cfe1eefdeea1e8e0f9"><span class="__cf_email__" data-cfemail="0563772b6c6b76756066716c6a6b456b6477642b626a73">[email protected]</span></a>, or go to <a href="https://www.archives.gov/federal-register/cfr/ibr-locations.html">https://www.archives.gov/federal-register/cfr/ibr-locations.html</a>.
Issued on September 20, 2021.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification
Service.
[FR Doc. 2021-22470 Filed 10-15-21; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.