Proposed Rule2021-20521
Airworthiness Directives; Bell Textron Canada Limited Helicopters
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
September 24, 2021
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA proposes to adopt a new airworthiness directive (AD) for Bell Textron Canada Limited Model 206L-1, 206L-3, and 206L-4 helicopters with certain Air Comm Corporation (Air Comm) air conditioning systems installed. This proposed AD would require visually inspecting the drive ring spline teeth and the mating area spline teeth on the oil cooler blower shaft for signs of deformation and fretting and depending on the results of the inspection, removing certain parts from service. This proposed AD would also require reinstalling certain parts, applying torque, and aligning certain bolt holes. This proposed AD was prompted by reports of damage to the drive ring spline teeth and the mating spline teeth. The actions of this proposed AD are intended to address an unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 86 Issue 183 (Friday, September 24, 2021)</title>
</head>
<body><pre>
[Federal Register Volume 86, Number 183 (Friday, September 24, 2021)]
[Proposed Rules]
[Pages 53015-53018]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2021-20521]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2021-0830; Project Identifier AD-2020-00257-R]
RIN 2120-AA64
Airworthiness Directives; Bell Textron Canada Limited Helicopters
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for Bell Textron Canada Limited Model 206L-1, 206L-3, and 206L-4
helicopters with certain Air Comm Corporation (Air Comm) air
conditioning systems installed. This proposed AD would require visually
inspecting the drive ring spline teeth and the mating area spline teeth
on the oil cooler blower shaft for signs of deformation and fretting
and depending on the results of the inspection, removing certain parts
from service. This proposed AD would also require reinstalling certain
parts, applying torque, and aligning certain bolt holes. This proposed
AD was prompted by reports of damage to the drive ring spline teeth and
the mating spline teeth. The actions of this proposed AD are intended
to address an unsafe condition on these products.
DATES: The FAA must receive comments on this proposed AD by November 8,
2021.
ADDRESSES: You may send comments by any of the following methods:
<bullet> Federal eRulemaking Portal: Go to <a href="https://www.regulations.gov">https://www.regulations.gov</a>. Follow the online instructions for sending your
comments electronically.
<bullet> Fax: (202) 493-2251.
<bullet> Mail: Send comments to the U.S. Department of
Transportation, Docket Operations, M-30, West Building Ground Floor,
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590-0001.
<bullet> Hand Delivery: Deliver to Mail address between 9 a.m. and
5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this proposed rule, contact
Air Comm Corporation, 1575 Westminster, CO 80234; telephone (303) 440-
4075; or at <a href="https://www.aircommcorp.com">https://www.aircommcorp.com</a>. You may view the referenced
service information at the FAA, Office of the Regional Counsel,
Southwest Region, 10101 Hillwood Pkwy., Room 6N-321, Fort Worth, TX
76177.
Examining the AD Docket
You may examine the AD docket on the internet at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No. FAA-2021-
0830; or in person at Docket Operations between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays. The AD docket contains
this NPRM, any referenced service information, any comments received,
and other information. The street address for Docket Operations is
listed above.
FOR FURTHER INFORMATION CONTACT: Matthew Bryant, Aerospace Engineer,
Denver ACO Branch, FAA, 26805 East 68th Avenue, Denver, CO 80249;
[[Page 53016]]
telephone (303) 342-1080; email <a href="/cdn-cgi/l/email-protection#635a4e27060d1506114e220a1100110205174e20061117230502024d040c15"><span class="__cf_email__" data-cfemail="e4ddc9a0818a928196c9a58d968796858290c9a7819690a4828585ca838b92">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under ADDRESSES. Include ``Docket No. FAA-2021-0830; Project Identifier
AD-2020-00257-R'' at the beginning of your comments. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing date and may amend
this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
<a href="https://www.regulations.gov">https://www.regulations.gov</a>, including any personal information you
provide. The agency will also post a report summarizing each
substantive verbal contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to
Matthew Bryant, Aerospace Engineer, Denver ACO Branch, FAA, 26805 East
68th Avenue, Denver, CO 80249; telephone (303) 342-1080; email <a href="/cdn-cgi/l/email-protection#5c65711839322a392e711d352e3f2e3d3a28711f392e281c3a3d3d723b332a"><span class="__cf_email__" data-cfemail="d9e0f49dbcb7afbcabf498b0abbaabb8bfadf49abcabad99bfb8b8f7beb6af">[email protected]</span></a>. Any commentary that the FAA receives
which is not specifically designated as CBI will be placed in the
public docket for this rulemaking.
Background
The FAA issued Special Airworthiness Information Bulletin SW-19-05
on April 4, 2019 (SAIB SW-19-05) to alert owners and operators of Bell
Textron Canada Limited Model 206L-1, 206L-3, and 206L-4 helicopters
with Air Comm's Supplemental Type Certificate (STC) SH2750NM installed.
SAIB SW-19-05 was prompted by reports of the air conditioner pulley's
locking system, which is installed on the oil cooler drive shaft's
splined quill, causing excessive spline tooth wear to the drive ring
spline teeth and the mating spline teeth on the oil cooler blower
shaft. SAIB SW-19-05 recommends following the inspection instructions
of certain Air Comm service information and routinely inspecting the
air conditioner pulley lock ring.
At the time SAIB SW-19-05 was issued, the airworthiness concern was
not determined to be an unsafe condition that would warrant AD action
under 14 CFR part 39. However, subsequent investigations were not able
to determine whether the limited damaged observed on several oil cooler
blower shafts would remain localized or progress to a point where the
shaft is no longer safe for continued use. The FAA also later
determined that operators may have difficulty aligning the air
conditioning system's drive ring holes with the air conditioning
condenser drive pulley without leaving the condenser drive pulley
under-torqued. Accordingly, the FAA proposes to adopt a new AD for
certain Bell Textron Canada Limited Model 206L-1 and 206L-3 helicopters
with Bell Model 206L1/L3 Service Instruction for Increased Gross Weight
Upgrade Kit BHT-206-SI-2052, Revision 1, dated October 14, 2010,
installed and Bell Model 206L-4 helicopters equipped with one of the
following Air Comm STC SH2750NM air conditioning systems part number
206EC-204-1, 206EC-204-2, 206EC-208-1, 206EC-208-2, 206EC-210-1, 206EC-
210-2, 206EC-210-3, 206EC-212-3 or 206EC-212-4. Helicopters with a
206L-1+ designation are Model 206L-1 helicopters and helicopters with a
206L-3+ designation are Model 206L-3 helicopters.
FAA's Determination
The FAA is issuing this NPRM after determining that the unsafe
condition described previously is likely to exist or develop on other
products of the same type design.
Related Service Information Under 1 CFR Part 51
The FAA reviewed ACC Air Comm Corporation Service Bulletin SB
206EC-091119, Rev B, dated May 26, 2021 (SB 206EC-091119 Rev B), which
specifies procedures for visually inspecting the drive ring spline
teeth and the mating spline teeth on the tail rotor drive's oil cooler
blower shaft for deformation or fretting.
This service information is reasonably available because the
interested parties have access to it through their normal course of
business or by the means identified in the ADDRESSES section.
Proposed AD Requirements in This NPRM
This proposed AD would require, within 300 hours time-in-service
(TIS), and thereafter at intervals not to exceed 300 hours TIS, gaining
access to the drive ring spline teeth and the mating area spline teeth
on the oil cooler blower shaft, repetitively inspecting the drive ring
spline teeth and the mating spline teeth on the tail rotor drive's oil
cooler blower shaft for deformation and fretting, and depending on the
results of each inspection, removing certain parts from service before
further flight. This proposed AD would also require reinstalling
certain parts, and if required, reinstalling the drive pulley by
torqueing and aligning the drive pulley bolt holes.
Differences Between This Proposed AD and the Service Bulletin
SB 206EC-091119 Rev B requires inspecting the air conditioning
compressor drive belt tension and the general condition of the drive
belt, drive pulley and surrounding components, whereas this proposed AD
would not. SB 206EC-091119 Rev B requires reporting any deformation or
fretting to Air Comm Service Department, whereas this proposed AD would
not. SB 206EC-091119 Rev B provides an option to deactivate the air
conditioning system if deformation of fretting is found on the drive
ring or the oil cooler blower shaft assembly, whereas this proposed AD
would require removing these parts from service instead.
Costs of Compliance
The FAA estimates that this proposed AD would affect up to 100
helicopters of U.S. Registry. The FAA estimates that operators may
incur the following costs in order to comply with this proposed AD.
Labor costs are estimated at $85 per work-hour.
Removing the tail rotor drive system's forward short shaft, spline
adaptor, and drive ring and visually inspecting the drive ring spline
teeth and the mating area spline teeth would take about 1 work-hour for
an estimated cost of $85 per helicopter and $8,500 for the U.S. fleet
per inspection cycle.
Replacing the drive ring would take about 3 work-hours and parts
would cost about $300 for an estimated cost of $555 per replacement.
[[Page 53017]]
Replacing the oil cooler blower assembly would take about 3 work-
hours and parts would cost about $2,720 for an estimated cost of $2,975
per replacement.
Aligning each bolt hole and re-torqueing the drive pulley would
take about 0.5 work-hours for an estimated cost of $43 per helicopter.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed, I certify this proposed regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866,
2. Would not affect intrastate aviation in Alaska, and
3. Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
Bell Textron Canada Limited: Docket No. FAA-2021-0830; Project
Identifier AD-2020-00257-R.
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive
(AD) by November 8, 2021.
(b) Affected ADs
None.
(c) Applicability
This AD applies to the Bell Textron Canada Limited helicopters
identified in paragraphs (c)(1) and (2) of this AD.
(1) Model 206L-1 and Model 206L-3 helicopters, certificated in
any category, with Bell Model 206L1/L3 Service Instruction for
Increased Gross Weight Upgrade Kit BHT-206-SI-2052, Revision 1,
dated October 14, 2010 (BHT-206-SI-2052), installed and that are
equipped with one of the following Air Comm Corporation (Air Comm)
Supplemental Type Certificate (STC) SH2750NM air conditioning
systems part number (P/N) 206EC-204-1, 206EC-204-2, 206EC-208-1,
206EC-208-2, 206EC-210-1, 206EC-210-2, 206EC-210-3, 206EC-212-3, or
206EC-212-4.
Note 1 to paragraph (c)(1) of this AD: Helicopters with a 206L-
1+ designation are Model 206L-1 helicopters and helicopters with a
206L-3+ designation are Model 206L-3 helicopters.
(2) Model 206 L-4 helicopters, certificated in any category, and
that are equipped with one of the following Air Comm STC SH2750NM
air conditioning systems P/N 206EC-204-1, 206EC-204-2, 206EC-208-1,
206EC-208-2, 206EC-210-1, 206EC-210-2, 206EC-210-3, 206EC-212-3, or
206EC-212-4.
(d) Subject
Joint Aircraft Service Component (JASC) Code: 6510, Tail Rotor
Drive Shaft.
(e) Unsafe Condition
This AD was prompted by reports of deformation or fretting of
the spline teeth on the air conditioning system and on the oil
cooler blower shaft. The FAA is issuing this AD to detect
deformation and fretting. The unsafe condition, if not addressed,
could result in a failure of the oil cooler blower shaft, which
could lead to loss of tail rotor authority and subsequent loss of
helicopter control.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Actions
Within 300 hours time-in-service (TIS) after the effective date
of this AD, and thereafter at intervals not to exceed 300 hours TIS:
(1) Gain access to the drive ring spline teeth and the mating
area spline teeth on the oil cooler blower shaft by removing the
tail rotor drive system's forward short shaft and spline adaptor,
and the air conditioner system's drive ring. Refer to Figure 1 of
ACC Air Comm Corporation Service Bulletin SB 206EC-091119, Rev B,
dated May 26, 2021 for a depiction of each component's location.
(2) Visually inspect the drive ring spline teeth and the mating
area spline teeth on the oil cooler blower shaft for deformation and
fretting.
(i) If there is deformation or fretting on the drive ring spline
teeth, before further flight, remove the drive ring from service and
replace it with an airworthy part.
(ii) If there is deformation or fretting on the mating area
spline teeth of the oil cooler blower shaft, before further flight,
remove the oil cooler blower assembly from service and replace with
an airworthy part.
(3) Reinstall the drive ring, spline adapter, and the forward
short shaft. If the compressor drive pulley was or removed, torque
the drive pulley to 200-300 in-lbs, increasing torque in this range
to align the four threaded holes with the through holes in the drive
ring. Do not back-off torque to align the bolt holes.
(h) Special Flight Permits
Special flight permits are prohibited.
(i) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Denver ACO, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. In accordance with 14 CFR 39.19, send your request to your
principal inspector or local Flight Standards District Office, as
appropriate. If sending information directly to the manager of the
Denver ACO, send it to the attention of the person identified in
paragraph (j)(1) of this AD. Information may be emailed to: <a href="/cdn-cgi/l/email-protection#b28b9ff6d7dcc4d7c09ff3dbc0d1c0d3d4c69ff1d7c0c6f2d4d3d39cd5ddc4"><span class="__cf_email__" data-cfemail="cef7e38aaba0b8abbce38fa7bcadbcafa8bae38dabbcba8ea8afafe0a9a1b8">[email protected]</span></a>.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(j) Related Information
(1) For more information about this AD, contact Matthew Bryant,
Aerospace Engineer, Denver ACO Branch, FAA, 26805 East 68th Avenue,
Denver, CO 80249; telephone (303) 342-1092; email <a href="/cdn-cgi/l/email-protection#93aabed7f6fde5f6e1bed2fae1f0e1f2f5e7bed0f6e1e7d3f5f2f2bdf4fce5"><span class="__cf_email__" data-cfemail="3a03177e5f544c5f48177b534859485b5c4e17795f484e7a5c5b5b145d554c">[email protected]</span></a>.
(2) For service information identified in this AD, contact Air
Comm Corporation, 1575 W 124th Ave. #210, Westminster, CO 80234;
telephone: (303) 440-4075; email <a href="/cdn-cgi/l/email-protection#2a495a45595c43496a4b4358494547474945585a04494547"><span class="__cf_email__" data-cfemail="284b58475b5e414b6849415a4b4745454b475a58064b4745">[email protected]</span></a>. You may
view the referenced service information at the FAA, Office of the
Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-
321, Fort Worth, TX 76177. For information on the availability of
this material at the FAA, call (817) 222-5110.
[[Page 53018]]
Issued on September 16, 2021.
Ross Landes,
Deputy Director for Regulatory Operations, Compliance & Airworthiness
Division, Aircraft Certification Service.
[FR Doc. 2021-20521 Filed 9-23-21; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on September 24, 2021.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.