Proposed Rule2021-18253
Airworthiness Directives; Costruzioni Aeronautiche Tecnam S.P.A. Airplanes
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
August 25, 2021
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA proposes to adopt a new airworthiness directive (AD) for all Costruzioni Aeronautiche Tecnam S.P.A. Model P2006T airplanes. This proposed AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a manufacturing defect in the nose landing gear (NLG) piston tube. This proposed AD would require replacing the NLG piston tube. The FAA is proposing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 86 Issue 162 (Wednesday, August 25, 2021)</title>
</head>
<body><pre>
[Federal Register Volume 86, Number 162 (Wednesday, August 25, 2021)]
[Proposed Rules]
[Pages 47422-47424]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2021-18253]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2021-0700; Project Identifier 2019-CE-017-AD]
RIN 2120-AA64
Airworthiness Directives; Costruzioni Aeronautiche Tecnam S.P.A.
Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for all Costruzioni Aeronautiche Tecnam S.P.A. Model P2006T airplanes.
This proposed AD was prompted by mandatory continuing airworthiness
information (MCAI) originated by an aviation authority of another
country to identify and correct an unsafe condition on an aviation
product. The MCAI describes the unsafe condition as a manufacturing
defect in the nose landing gear (NLG) piston tube. This proposed AD
would require replacing the NLG piston tube. The FAA is proposing this
AD to address the unsafe condition on these products.
DATES: The FAA must receive comments on this proposed AD by October 12,
2021.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
<bullet> Federal eRulemaking Portal: Go to <a href="https://www.regulations.gov">https://www.regulations.gov</a>. Follow the instructions for submitting comments.
<bullet> Fax: (202) 493-2251.
<bullet> Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
<bullet> Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this NPRM, contact
Costruzioni Aeronautiche Tecnam S.P.A, Via S. D'acquisto 62, 80042
Boscotrecase (NA), Italy; phone: + 39 0823 620134; fax: +
[[Page 47423]]
39 0823 622899; email: <a href="/cdn-cgi/l/email-protection#e988809b9e869b9d8180878c9a9aa99d8c8a878884c78a8684"><span class="__cf_email__" data-cfemail="ea8b83989d85989e8283848f9999aa9e8f89848b87c4898587">[email protected]</span></a>; website: <a href="https://www.tecnam.com/us/support/">https://www.tecnam.com/us/support/</a>. You may view this service information at
the FAA, Airworthiness Products Section, Operational Safety Branch, 901
Locust, Kansas City, MO 64106. For information on the availability of
this material at the FAA, call (816) 329-4148.
Examining the AD Docket
You may examine the AD docket at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by
searching for and locating Docket No. FAA-2021-0700; or in person at
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The AD docket contains this NPRM, the MCAI,
any comments received, and other information. The street address for
Docket Operations is listed above.
FOR FURTHER INFORMATION CONTACT: Jim Rutherford, Aviation Safety
Engineer, General Aviation & Rotorcraft Section, International
Validation Branch, FAA, 901 Locust, Room 301, Kansas City, MO 64106;
phone: (816) 329-4165; fax: (816) 329-4090; email:
<a href="/cdn-cgi/l/email-protection#72181b1f5c0007061a1700141d0016321413135c151d04"><span class="__cf_email__" data-cfemail="c2a8abafecb0b7b6aaa7b0a4adb0a682a4a3a3eca5adb4">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under ADDRESSES. Include ``Docket No. FAA-2021-0700; Project Identifier
2019-CE-017-AD'' at the beginning of your comments. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing date and may amend
this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
<a href="https://www.regulations.gov">https://www.regulations.gov</a>, including any personal information you
provide. The agency will also post a report summarizing each
substantive verbal contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to Jim
Rutherford, Aviation Safety Engineer, General Aviation & Rotorcraft
Section, International Validation Branch, FAA, 901 Locust, Room 301,
Kansas City, MO 64106. Any commentary that the FAA receives which is
not specifically designated as CBI will be placed in the public docket
for this rulemaking.
Background
The European Union Aviation Safety Agency (EASA), which is the
Technical Agent for the Member States of the European Union, has issued
EASA AD 2019-0043, dated March 6, 2019 (referred to after this as ``the
MCAI''), to correct an unsafe condition on Costruzioni Aeronautiche
Tecnam S.P.A. Model P2006T airplanes. The MCAI states:
Failures of NLG piston tubes P/N 26-8-1408-1 were reported
during ground operations. Subsequent investigation determined a
deficiency in NLG piston tube manufacturing process. It was also
determined that only a specific batch is affected by this defect.
This condition, if not corrected, could lead to failure of the
NLG, possibly resulting in loss of control on the ground, during or
after landing, with consequent damage to the aeroplane and injury to
occupants.
To address this potential unsafe condition, TECNAM issued the
[service bulletin] SB to provide instructions for the replacement of
each affected part with a part that was manufactured by an improved
process.
For the reasons described above, this [EASA] AD requires removal
from service of the affected parts.
You may examine the MCAI in the AD docket at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No. FAA-2021-
0700.
Related Service Information
Costruzioni Aeronautiche Tecnam S.P.A. Service Bulletin No. SB 288-
CS-Ed 1, Revision 1, dated December 22, 2017, is related to this NPRM
and provides information about installing nose landing gear (NLG)
piston tube kit number SB 288-1.
FAA's Determination
This product has been approved by the aviation authority of another
country and is approved for operation in the United States. Pursuant to
the FAA's bilateral agreement with this State of Design Authority, it
has notified the FAA of the unsafe condition described in the MCAI and
service information referenced above. The FAA is issuing this NPRM
after determining the unsafe condition described previously is likely
to exist or develop on other products of the same type design.
Proposed AD Requirements in This NPRM
This proposed AD would require replacing NLG piston tubes that are
not P/N 26-8-1408-1 and marked ``rev F00.''
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would
affect 59 airplanes of U.S. registry. The FAA also estimates that it
would take about 4 work-hours per airplane to comply with the
replacement required by this proposed AD. The average labor rate is $85
per work-hour. Required parts would cost about $1,200 per airplane.
Based on these figures, the FAA estimates the cost of this proposed
AD on U.S. operators to be $90,860, or $1,540 per airplane.
The FAA has included all known costs in its cost estimate.
According to the manufacturer, however, some of the costs of this
proposed AD may be covered under warranty, thereby reducing the cost
impact on affected operators.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
[[Page 47424]]
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
Costruzioni Aeronautiche Tecnam S.P.A.: Docket No. FAA-2021-0700;
Project Identifier 2019-CE-017-AD.
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive
(AD) by October 12, 2021.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Costruzioni Aeronautiche Tecnam S.P.A. Model
P2006T airplanes, all serial numbers, certificated in an category.
(d) Subject
Joint Aircraft System Component (JASC) Code 3220, Nose/Tail
Landing Gear.
(e) Unsafe Condition
This AD was prompted by mandatory continuing airworthiness
information (MCAI) originated by an aviation authority of another
country to identify and address an unsafe condition on an aviation
product. The MCAI describes the unsafe condition as a manufacturing
defect in the nose landing gear (NLG) piston tube. The unsafe
condition, if not addressed, could result in failure of the NLG upon
or after landing.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Required Actions
(1) For airplanes with an NLG piston tube part number (P/N) 26-
8-1408-1 installed and not marked ``rev. F00'': Within 50 hours
time-in-service after the effective date of this AD or within 2
months after the effective date of this AD, whichever occurs first,
replace any P/N 26-8-1408-1 NLG piston tube with an improved part by
installing NLG piston tube kit number SB 288-1.
(2) As of the effective date of this AD, do not install an NLG
piston tube P/N 26-8-1408-1 on any airplane unless it is marked
``rev. F00.''
(h) Alternative Methods of Compliance (AMOCs)
(1) The Manager, International Validation Branch, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the certification office, send it to the
attention of the person identified in Related Information or email:
<a href="/cdn-cgi/l/email-protection#2a13076b7c79076b6378071d191a076b6765696a4c4b4b044d455c"><span class="__cf_email__" data-cfemail="152c3854434638545c47382226253854585a56557374743b727a63">[email protected]</span></a>.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(i) Related Information
(1) For more information about this AD contact Jim Rutherford,
Aviation Safety Engineer, General Aviation & Rotorcraft Section,
International Validation Branch, FAA, 901 Locust, Room 301, Kansas
City, MO 64106; phone: (816) 329-4165; fax: (816) 329-4090; email:
<a href="/cdn-cgi/l/email-protection#bad0d3d794c8cfced2dfc8dcd5c8defadcdbdb94ddd5cc"><span class="__cf_email__" data-cfemail="aec4c7c380dcdbdac6cbdcc8c1dccaeec8cfcf80c9c1d8">[email protected]</span></a>.
(2) Refer to European Union Aviation Safety Agency (EASA) AD
2019-0043, dated March 6, 2019, for more information. You may
examine the EASA AD in the AD docket at <a href="https://www.regulations.gov">https://www.regulations.gov</a>
by searching for and locating Docket No. FAA-2021-0700.
(3) For service information identified in this AD, contact
Costruzioni Aeronautiche Tecnam S.P.A, Via S. D'acquisto 62, 80042
Boscotrecase (NA), Italy; phone: + 39 0823 620134; fax: + 39 0823
622899; email: <a href="/cdn-cgi/l/email-protection#aecfc7dcd9c1dcdac6c7c0cbddddeedacbcdc0cfc380cdc1c3"><span class="__cf_email__" data-cfemail="ed8c849f9a829f99858483889e9ead99888e838c80c38e8280">[email protected]</span></a>; website: <a href="https://www.tecnam.com/us/support/">https://www.tecnam.com/us/support/</a>. You may review this referenced service
information at the FAA, Airworthiness Products Section, Operational
Safety Branch, 901 Locust, Kansas City, MO 64106. For information on
the availability of this material at the FAA, call (816) 329-4148.
Issued on August 19, 2021.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness
Division, Aircraft Certification Service.
[FR Doc. 2021-18253 Filed 8-24-21; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on August 25, 2021.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.