Proposed Rule2021-17949
Airworthiness Directives; Leonardo S.p.a. Helicopters
Primary source
Metadata and text below are from the Federal Register, a public-domain U.S. government work. Always verify the official published version before relying on it for any legal matter.
Published
August 23, 2021
Issuing agencies
Transportation DepartmentFederal Aviation Administration
Abstract
The FAA proposes to adopt a new airworthiness directive (AD) for certain Leonardo S.p.a. Model AW189 helicopters. This proposed AD was prompted by a report that a number of fairleads that support the engine combustion chamber D1 drain hose showed evidence of heat damage. This proposed AD would require modifying the helicopter by installing a certain engine combustion chamber D1 drain assembly, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Full Text
<html>
<head>
<title>Federal Register, Volume 86 Issue 160 (Monday, August 23, 2021)</title>
</head>
<body><pre>
[Federal Register Volume 86, Number 160 (Monday, August 23, 2021)]
[Proposed Rules]
[Pages 47033-47035]
From the Federal Register Online via the Government Publishing Office [<a href="http://www.gpo.gov">www.gpo.gov</a>]
[FR Doc No: 2021-17949]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2021-0687; Project Identifier 2019-SW-029-AD]
RIN 2120-AA64
Airworthiness Directives; Leonardo S.p.a. Helicopters
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for certain Leonardo S.p.a. Model AW189 helicopters. This proposed AD
was prompted by a report that a number of fairleads that support the
engine combustion chamber D1 drain hose showed evidence of heat damage.
This proposed AD would require modifying the helicopter by installing a
certain engine combustion chamber D1 drain assembly, as specified in a
European Union Aviation Safety Agency (EASA) AD, which is proposed for
incorporation by reference (IBR). The FAA is proposing this AD to
address the unsafe condition on these products.
DATES: The FAA must receive comments on this proposed AD by October 7,
2021.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
<bullet> Federal eRulemaking Portal: Go to <a href="https://www.regulations.gov">https://www.regulations.gov</a>. Follow the instructions for submitting comments.
<bullet> Fax: (202) 493-2251.
<bullet> Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
<bullet> Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For EASA material that is proposed for IBR in this AD, contact
EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221
8999 000; email <a href="/cdn-cgi/l/email-protection#bdfcf9cefdd8dccedc93d8c8cfd2cddc93d8c8"><span class="__cf_email__" data-cfemail="2a6b6e596a4f4b594b044f5f58455a4b044f5f">[email protected]</span></a>; internet www.easa.europa.eu. You
may find the EASA material on the EASA website at <a href="https://ad.easa.europa.eu">https://ad.easa.europa.eu</a>. You may view this material at the FAA, Office of the
Regional Counsel, Southwest Region, 10101 Hillwood Pkwy., Room 6N-321,
Fort Worth, TX 76177. For information on the availability of this
material at the FAA, call (817) 222-5110. This material is also
available at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating
Docket No. FAA-2021-0687.
Examining the AD Docket
You may examine the AD docket at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by
searching for and locating Docket No. FAA-2021-0687; or in person at
Docket Operations between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The AD docket contains this NPRM, the EASA AD,
any comments received, and other information. The street address for
Docket Operations is listed above.
[[Page 47034]]
FOR FURTHER INFORMATION CONTACT: Jacob Fitch, Aerospace Engineer, COS
Program Management Section, Operational Safety Branch, Compliance &
Airworthiness Division, FAA, 10101 Hillwood Pkwy., Fort Worth, TX
76177; telephone (817) 222-4130; email <a href="/cdn-cgi/l/email-protection#137972707c713d757a67707b537572723d747c65"><span class="__cf_email__" data-cfemail="3b515a585459155d524f58537b5d5a5a155c544d">[email protected]</span></a>.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under ADDRESSES. Include ``Docket No. FAA-2021-0687; Project Identifier
2019-SW-029-AD'' at the beginning of your comments. The most helpful
comments reference a specific portion of the proposal, explain the
reason for any recommended change, and include supporting data. The FAA
will consider all comments received by the closing date and may amend
this proposal because of those comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, to
<a href="https://www.regulations.gov">https://www.regulations.gov</a>, including any personal information you
provide. The agency will also post a report summarizing each
substantive verbal contact received about this NPRM.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to Jacob
Fitch, Aerospace Engineer, COS Program Management Section, Operational
Safety Branch, Compliance & Airworthiness Division, FAA, 10101 Hillwood
Pkwy., Fort Worth, TX 76177; telephone (817) 222-4130; email
<a href="/cdn-cgi/l/email-protection#ee848f8d818cc088879a8d86ae888f8fc0898198"><span class="__cf_email__" data-cfemail="f09a91939f92de9699849398b0969191de979f86">[email protected]</span></a>. Any commentary that the FAA receives that is not
specifically designated as CBI will be placed in the public docket for
this rulemaking.
Background
The EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2019-0039, dated February 20, 2019
(EASA AD 2019-0039), to correct an unsafe condition for certain
Leonardo S.p.A. Model AW189 helicopters.
This proposed AD was prompted by a report that a number of
fairleads that support the engine combustion chamber D1 drain hose
showed evidence of heat damage. The FAA is proposing this AD to address
heat damage, which in a case where the right-hand engine is operated in
the one engine inoperative (OEI) rating, the D1 drain pipe could
transfer so much heat to the nearby fuel system vent pipe that its
internal surface temperature could exceed the auto-ignition temperature
for fuel. The unsafe condition, if not addressed, could result in
undetected fire ignition in the fuel tank bay with consequent loss of
the helicopter. See EASA AD 2019-0039 for additional background
information.
Related Service Information Under 1 CFR Part 51
EASA AD 2019-0039 requires modifying the helicopter by installing
the engine combustion chamber D1 drain assembly, part number
8G7170P00111.
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
FAA's Determination
This helicopter has been approved by EASA and is approved for
operation in the United States. Pursuant to the FAA's bilateral
agreement with the European Union, EASA has notified the FAA about the
unsafe condition described in its AD. The FAA is proposing this AD
after evaluating all known relevant information and determining that
the unsafe condition described previously is likely to exist or develop
on other helicopters of the same type design.
Proposed AD Requirements in This NPRM
This proposed AD would require accomplishing the actions specified
in EASA AD 2019-0039, described previously, as incorporated by
reference, except for any differences identified as exceptions in the
regulatory text of this proposed AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA developed a process to use some civil aviation
authority (CAA) ADs as the primary source of information for compliance
with requirements for corresponding FAA ADs. The FAA has been
coordinating this process with manufacturers and CAAs. As a result, the
FAA proposes to incorporate EASA AD 2019-0039 by reference in the FAA
final rule. This proposed AD would, therefore, require compliance with
EASA AD 2019-0039 in its entirety through that incorporation, except
for any differences identified as exceptions in the regulatory text of
this proposed AD. Using common terms that are the same as the heading
of a particular section EASA AD 2019-0039 does not mean that operators
need comply only with that section. For example, where the AD
requirement refers to ``all required actions and compliance times,''
compliance with this AD requirement is not limited to the section
titled ``Required Action(s) and Compliance Time(s)'' in EASA AD 2019-
0039. Service information required by EASA AD 2019-0039 for compliance
will be available at <a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and
locating Docket No. FAA-2021-0687 after the FAA final rule is
published.
Costs of Compliance
The FAA estimates that this AD, if adopted as proposed, would
affect 4 helicopters of U.S. registry. The FAA estimates the following
costs to comply with this proposed AD:
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Action Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
Modification.......................... 4 work-hours x $85 per $2,557 $2,897 $11,588
hour = $340.
----------------------------------------------------------------------------------------------------------------
[[Page 47035]]
The FAA has included all known costs in its cost estimate.
According to the manufacturer, however, some or all of the costs of
this proposed AD may be covered under warranty, thereby reducing the
cost impact on affected operators.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Would not affect intrastate aviation in Alaska, and
(3) Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive:
Leonardo S.p.a.: Docket No. FAA-2021-0687; Project Identifier 2019-
SW-029-AD.
(a) Comments Due Date
The FAA must receive comments on this airworthiness directive
(AD) by October 7, 2021.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Leonardo S.p.a. Model AW189 helicopters,
certificated in any category, as identified in European Union
Aviation Safety Agency (EASA) AD 2019-0039, dated February 20, 2019
(EASA AD 2019-0039).
(d) Subject
Joint Aircraft Service Component (JASC) Code: 7170, Engine
Drains.
(e) Unsafe Condition
This AD was prompted by a report that a number of fairleads that
support the engine combustion chamber D1 drain hose showed evidence
of heat damage. The FAA is issuing this AD to address such heat
damage, which in a case where the right-hand engine is operated in
the one engine inoperative (OEI) rating, the D1 drain pipe could
transfer so much heat to the nearby fuel system vent pipe that its
internal surface temperature could exceed the auto-ignition
temperature for fuel. The unsafe condition, if not addressed, could
result in undetected fire ignition in the fuel tank bay with
consequent loss of the helicopter.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, EASA AD 2019-0039.
(h) Exceptions to EASA AD 2019-0039
(1) Where EASA AD 2019-0039 requires compliance in terms of
flight hours, this AD requires using hours time-in-service.
(2) Where EASA AD 2019-0039 refers to its effective date, this
AD requires using the effective date of this AD.
(3) Where the service information required by EASA AD 2019-0039
specifies discarding parts, this AD requires removing those parts
from service.
(4) This AD does not require the ``Remarks'' section of EASA AD
2019-0039.
(i) No Reporting Requirement
Although the service information referenced in EASA AD 2019-0039
specifies to submit certain information to the manufacturer, this AD
does not include that requirement.
(j) Special Flight Permit
Special flight permits may be issued in accordance with 14 CFR
21.197 and 21.199 to operate the airplane to a location where the
airplane can be modified, provided the OEI rating is prohibited on
the right-hand engine.
(k) Alternative Methods of Compliance (AMOCs)
(1) The Manager, International Validation Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the manager of the International Validation Branch, send
it to the attention of the person identified in paragraph (l)(2) of
this AD. Information may be emailed to: <a href="/cdn-cgi/l/email-protection#c0f9ed819693ed818992edf7f3f0ed818d8f8380a6a1a1eea7afb6"><span class="__cf_email__" data-cfemail="e1d8cca0b7b2cca0a8b3ccd6d2d1cca0acaea2a1878080cf868e97">[email protected]</span></a>.
(2) Before using any approved AMOC, notify your appropriate
principal inspector, or lacking a principal inspector, the manager
of the local flight standards district office/certificate holding
district office.
(l) Related Information
(1) For EASA AD 2019-0039, contact EASA, Konrad-Adenauer-Ufer 3,
50668 Cologne, Germany; telephone +49 221 8999 000; email
<a href="/cdn-cgi/l/email-protection#c78683b487a2a6b4a6e9a2b2b5a8b7a6e9a2b2"><span class="__cf_email__" data-cfemail="6d2c291e2d080c1e0c4308181f021d0c430818">[email protected]</span></a>; internet www.easa.europa.eu. You may view this
material at the FAA, Office of the Regional Counsel, Southwest
Region, 10101 Hillwood Pkwy., Room 6N-321, Fort Worth, TX 76177. For
information on the availability of this material at the FAA, call
(817) 222-5110. This material may be found in the AD docket at
<a href="https://www.regulations.gov">https://www.regulations.gov</a> by searching for and locating Docket No.
FAA-2021-0687.
(2) For more information about this AD, contact Jacob Fitch,
Aerospace Engineer, COS Program Management Section, Operational
Safety Branch, Compliance & Airworthiness Division, FAA, 10101
Hillwood Pkwy., Fort Worth, TX 76177; telephone (817) 222-4130;
email <a href="/cdn-cgi/l/email-protection#8ae0ebe9e5e8a4ece3fee9e2caecebeba4ede5fc"><span class="__cf_email__" data-cfemail="107a71737f723e7679647378507671713e777f66">[email protected]</span></a>.
Issued on August 17, 2021.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness
Division, Aircraft Certification Service.
[FR Doc. 2021-17949 Filed 8-20-21; 8:45 am]
BILLING CODE 4910-13-P
</pre><script data-cfasync="false" src="/cdn-cgi/scripts/5c5dd728/cloudflare-static/email-decode.min.js"></script></body>
</html>Indexed from Federal Register on August 23, 2021.
This is legal information, not legal advice. Laws vary by jurisdiction and change frequently. Always verify current law with official sources and consult a licensed attorney in your jurisdiction for advice on your specific situation.